M4NN Series. Small Multi Panel Meter. DIN W48 H24mm Small Digital Multi Panel Meter Features. Ordering information.

Transcription

1 4NN eries mll ulti Pnel eter DIN W48 H24mm mll Digitl ulti Pnel eter Fetures Upgrded of 4N eries 1 power enles to supply the power to severl 4NN units y insulting input nd power prt rnge: to 9999 Power supply: 5-24VDC (insultion type) Preset output:, GO, OUT2 (NPN/PNP open collector output ) Power fctor disply nd output : displys input of 1-5V, 4 to 20m, etc s -0.5 to 1 to 0.5 Vrious input types/indictor DC voltge model: ±200mV/±1V/±2V/±10V/±20V/±100V/±200V/±600V/power fctor DC current model: ±2m/±10m/±20m/4 to 20m/±100m/±200m/±1/±2/±5/power fctor C voltge model: 1V/2V/10V/20V/50V/110V/250V/600V/C frequency C current model: 50m/100m/250m/500m/1/2.5/5/C frequency Plese red Cution for your sfety in opertion mnul efore using. Ordering informtion 4 N N DV 1 N Item Digit ize Type Unit Description type N Control output Power supply Indictor (without output function) 1 NPN open collector output 2 PNP open collector output VDC DV D V N N DC Voltge (minus input) DC Current (minus input) C Voltge C Current New Type DIN W48 H24mm (4digit) ulti eter 1. esurement disply prt 2. : ODE key 3. : Up key 4. : hift key 5. (red): output indictor of preset 6. GO (green): GO output indictor of preset 7. OUT2 (red): OUT2 output indictor of preset 8. Unit sticker Indictor model (4NN- -1N) does not hve trnsistor output terminl. Dimensions (unit: mm) 48 4 rcket Trnsistor output terminl 42 Pnel cut-out in. 50 () () Door/re Rotry ockets Temperture Rs / Power Pnel eters () Tcho / peed / Pulse eters ensor witching ode Power upplies tepper otors & Grphic/ Pnels () oftwre in Indictor model (4NN- -1N) does not hve trnsistor output terminl. L-5

2 4NN eries pecifictions odel 4NN-DV-1 4NN-D-1 4NN-V-1 4NN--1 DC voltge DC current C voltge, frequency C current, frequency x. llowle input -110 to 110% of the rted mesurement input rnge (when not using minus input: -10 to 110%) pprox. 110% of the rted mesurement input rnge Power supply 5-24 VDC llowle voltge rnge 90 to 110% of the rted voltge (5V is fixed for lower limit) Power consumption x. 3W method 7 segment LED (red), chrcter height: 11mm 23 ±5 -DC : ±0.1% F.. ±2digit / C ±0.3% F.. ±3digit ccurcy For 5 terminl of 4NN-D,, ±0.3% F.. ±3digit -10 to 50 -DC/C : ±0.5% F.. ±3digit / Frequency: ±0.5% F.. ±3digit For 5 terminl of 4NN-D,, ±1% F.. ±3digit cycle 0.1 to 5.0 sec. (selectle y 0.1 sec.) /D conversion method Prcticl oversmpling using successive pproximtion DC mpling cycle 50ms (resolution 1/12,000) 16.6ms (resolution 1/12,000) x. disply rnge to 9999 (4 digit) NPN/PNP open collector output: Preset output 1 Lod voltge: mx. 30VDC Lod current: mx. 100m Residul voltge: mx. 1VDC (NPN), mx. 2VDC (PNP) C mesurement 2 - verge (VG) mesurement Frequency mesurement 2 - esurement rnge: to 9999Hz (vrile y deciml point position) Insultion resistnce in. 100Ω (t 500VDC megger) Dielectric strength 2,000VC for 1 min. (etween ll terminls nd cse) Noise resistnce ±2kV the squre wve noise (pulse width: 1μs ) y the noise simultor Virtion echnicl 0.75mm mplitude t frequency of 10 to 55Hz (for 1 min.) in ech X, Y, Z direction for 2 hours lfunction 0.5mm mplitude t frequency of 10 to 55Hz (for 1 min.) in ech X, Y, Z direction for 10 min. hock echnicl 100m/s 2 (pprox. 10G) in ech X, Y, Z direction for 3 times lfunction 300m/s 2 (pprox. 30G) in ech X, Y, Z direction for 3 times Environment Connection Insultion type pprovl Connections 4NN-DV NN-V-1 mient temperture -10 to 50, storge: -20 to 60 mient humidity 35 to 85%RH, storge: 35 to 85%RH Plug/ocket terminl lock (ccessory) Doule insultion or reinforced insultion (mrk:, dielectric strength etween the mesured input prt nd the power prt: 1kV) 3 Weight pprox. 83.6g pprox. 83.7g pprox. 83.8g pprox. 83.8g (pprox. 46.8g) (pprox. 46.7g) (pprox. 46.9g) (pprox. 46.9g) 1: Indictor (4NN- -1N) model does not hve output function. 2: C, frequency mesurement functions re only for C mesurement type. 3: The weight includes pckging. The weight in prentheses is for unit only. Environment resistnce is rted t no freezing or condenstion DC ±600V/±200V C 600V/200V NPN Open Collector PNP Open Collector DC ±1V /±200mV - + DC±10V/±2V DC ±100V/±20V HOLD C 2V/1V C 20V/10V C 110V/50V GO OUT2 CO HOLD + - OURCE 5-24VDC OURCE 5-24VDC 4NN-D NN--1 nd output re insulted from the power Option output DC input circuit nd disply prt 4 5 DC ±10m /±2m - + DC±100m /±20m HOLD /4-20m DC ±1/200m DC ±5/±2 C 5/2.5 C C100m /C50m C500m /C250m 8 HOLD Power OURCE 5-24VDC OURCE 5-24VDC L-6 GO OUT2 CO

3 mll ulti Pnel eter Prmeter settings P0 for 2 sec. P1 P2 for 2 sec. for 3 sec. for 3 sec. () () Door/re Prmeter 1 group 3 sec. 2 sec. P1 IN-R INU esured input type 1 ON Prmeter setting 1. Ech prmeter lterntely displys prmeter nme nd the V in 0.5 sec. 2. Press the key nd the V is sved nd it moves to next prmeter. 3. If there is no opertion for 60 sec., it returns to utomticlly. 4. Press the keys for 3 sec. nd it returns to. 5. Press the, keys to chnge the V t the prmeter. ( : moves setting digit, : chnges set ) : Press ny key etween,. 1: Refer to type nd rnge. inus input disply (DC input only) Rotry ockets Temperture Rs / Power DIP method INH INL TND! CL DOT H-C L-C C voltge/current Deciml point position et rnge: et rnge: 0, )0, )00, )000 High-limit scle 1 Low-limit scle 1 Devition correction of high limit (grdient correction) et rnge: )100 to (999 (multiply) Devition correction of low limit (zero point) et rnge: -99 to 99 FREQ DOT INH INE Frequency Deciml point position et rnge: et rnge: 0, )0, )00, )000 ntiss of grdient correction for frequency et rnge of mntiss: )100 to (999 Index of grdient correction for frequency et rnge: 10 0, 10 1, 10-2, 10-1 DC voltge/current PF H-RG L-RG Power fctor High-limit input 1 Low-limit input 1 Pnel eters () Tcho / peed / Pulse eters ensor witching ode Power upplies tepper otors & Grphic/ Pnels () Fctory defult oftwre Prmeter 4NN-DV 4NN-D 4NN-V 4NN- Prmeter 4NN-DV 4NN-D 4NN-V 4NN- IN-R 600V 5 600V 5 INH!000!000!000!000 INU ON ON - - INL DIP TND TND TND TND H-RG 600 % DOT L-RG % H-C INE L-C L-7

4 4NN eries Prmeter 2 group 3 sec. P2 Prmeter (0 to 2) group setting method 1. Ech prmeter lterntely displys prmeter nme nd the V in 0.5 sec. 2. Press the key nd the V is sved nd it moves to next prmeter. 3. If there is no opertion for 60 sec., it returns to utomticlly. 4. Press the keys for 3 sec. nd it returns to. 5. Press the, keys to chnge the V t the prmeter. ( : moves setting digit, : chnges set ) : Press ny key etween,. OU!T Preset output opertion mode of (displyed only for OUT 1 output model) et rnge:, HI, LO, HL, HL-G OU@T HYs1 001 Preset output opertion mode of OUT2 (displyed only for OUT 2 output model) Preset hysteresis of et rnge: within 10% of mx. disply rnge (unit: digit) If disply resolution is over 10000, it is fixed s 999. When OU!T prmeter is, it is not displyed. HYs2 PEkT PEkT LOC )2 5 Preset hysteresis of OUT2 et rnge: within 10% of mx. disply rnge (unit: digit) If disply resolution is over 10000, it is fixed s 999. When OU@T prmeter is, it is not displyed. onitoring dely time of pek monitoring function et rnge: 00 to 30 sec. cycle et rnge: 0.1 to 5.0 sec. Lock mong 4 types. et rnge:, LOC1, LOC2, LOC3 LOC1 LOC2 LOC3 Unlock Lock Prmeter 1 group Lock Prmeter 1, 2 groups Lock Prmeter 0, 1, 2 groups Fctory defult Prmeter 4NN-DV 4NN-D 4NN-V 4NN- Prmeter 4NN-DV 4NN-D 4NN-V 4NN- OU!T 1 PEkT OU@T 1 DIsT )2 5 )2 5 )2 5 )2 5 HYs LOC HYs It is not displyed for the indictor model. Prmeter 0 group OU!H x. disply High-limit preset of Not displyed when OU!T prmeter is t Prmeter 2 group. OU!L in. disply Low-limit preset of Not displyed when OU!T prmeter is t Prmeter 2 group. OU@H x. disply High-limit preset of OUT2 Not displyed when OU@T prmeter is t Prmeter 2 group. OU@L hpek in. disply )0 Low-limit preset of OUT2 Not displyed when OU@T prmeter is t Prmeter 2 group. It displys mx. monitoring (high pek ) in. Press ny key etween, nd it is initilized (reset). hpek prmeter is not displyed when PEkT prmeter is set s 00 sec.[00 5] t Prmeter 2 group. lpek )0 It displys min. monitoring (low-limit ) in. Press ny key etween, nd it is initilized (reset). lpek prmeter is not displyed when PEkT prmeter is set s 00 sec.[00 5] t Prmeter 2 group. L-8

5 mll ulti Pnel eter Fctory defult Prmeter 4NN-DV 4NN-D 4NN-V 4NN- Prmeter 4NN-DV 4NN-D 4NN-V 4NN- OU!H %00 60)0 %000 OU@L %00 00)0 )000 OU!L %00 00)0 )000 hpek 1 0 )00 )0 )000 OU@H %00 60)0 %000 lpek 1 0 )00 )0 )000 It is not displyed for the indictor model. () () Door/re pecifiction of mesurement input nd rnge Type esured input rnge impednce rnge [ TND] Note DC voltge DC current C voltge C current V [600V] 4.694Ω -600 to V [200V] 4.694Ω to V [100V] 794kΩ to V [20V] 79kΩ to V [10V] 79kΩ to V [2V] 79kΩ to V [1V] 7.5kΩ to mV [)2V] 7.5kΩ to [] 0.01kΩ to [2] 0.01Ω to [1] 0.1Ω to m [)2] 0.1Ω to m [)1] 1.1Ω to m [20] 1.1Ω to m [4-20] 1.1Ω 4.00 to m [10] 11.1Ω to m [2] 11.1Ω to V [600V] 4.987Ω 0.0 to V [250V] 4.987Ω 0.0 to V [110P] 1.087Ω 0.0 to V [50V] 1.087Ω 0.00 to V [20V] 200kΩ 0.00 to V [10V] 200kΩ 0.00 to V [2V] 20kΩ to V [1V] 20kΩ to [5] 0.01Ω to [@5] 0.01Ω to [1] 0.05Ω to m [)5] 0.1Ω 0.0 to m [)25] 0.1Ω 0.0 to m [)1] 0.5Ω 0.0 to m [50] 0.5Ω 0.00 to For DC input, not to disply minus input, set minus input disply [INU] of prmeter 1 group s. E.g.) When the disply rnge is -600 to 600V, set INU of prmeter 1 group s nd this disply rnge is 0 to 600V. DOT rnge to 9999 ) to ) to ) to (disply rnge is vrile ccording to deciml point position) Plese wire proper terminl to its mx. input voltge within 30 to 100% of input terminl. When it is higher thn input voltge, it my cuse rekdown of terminl nd OVER disply rnge nd the ccurcy is decresed when it is connected to the terminl under 30%. For the rnge setting of C voltge, when setting s 0 to 110V[110P] nd using P.T for 440V/110VC, 110V is input nd 440V is displyed utomticlly y the set scle for P.T users' convenience. Frequency mesurement rnge (C voltge/current) : to 9999Hz Rotry ockets Temperture Rs / Power Pnel eters () Tcho / peed / Pulse eters ensor witching ode Power upplies tepper otors & Grphic/ Pnels () oftwre L-9

6 4NN eries Functions inus input disply [P 1 group: INU] When minus input is unnecessry, or when disply 0 not to disply minus input due to disply minus input due to unstle input round 0, set s this minus input disply function. When setting, low-limit of input rnge is set 0 nd it displys minus input s 0. The low-limit of L-C, OU.L, L-RG prmeters is chnged sed on "0". in. disply is "0" nd H-C, H-RG prmeters disply mx. of the input rnge. The INH / INL / OU.T / HY. / OU.H prmeters re initilized to fctory defult. In cse of DC current mesurement input model, when mesurement input rnge [IN-R] is set s 4-20, this prmeter is not displyed. C frequency mesurement [P 1 group: DIP ] It mesures input signl frequency when it is n C input. It uses fixed deciml point y DOT prmeter setting of prmeter 1 group, mesured rnge cn e chnged y setting nd mesured rnge of deciml point position is s elow chrt. It is ville to djust upper grdient t INH nd INE of prmeter 1 group. In order to mesure frequency normlly, input signl, over 10% F.. of the mesured rnge, should e supplied. Plese select the proper point of mesurement terminl. esurement rnge Dot position )000 )00 )0 0 esurement rnge to 9.999Hz 0.10 to 99.99Hz + for 3 sec. 0.1 to 999.9Hz 1 to 9999Hz ccurcy of frequency mesurement: elow 1kHz, F.. ±0.1rdg ±2digit, from 1 to 10kHz, F.. ±0.3 rdg ±2digit INH: to [grdient djustment of high-limit ] INE: 10-2, 10-1, 10 0, 10 1 [index djustment of INH] Zero djustment [low-limit disply devition correction] Forces the disply of mesured input to 0 (Zero). Zero djustment rnge: -99 to 99 Zero djustment method: Press nd key in RUN mode for 3 sec. )15 )00 When zero point djustment with front key nd hold terminl is finished normlly, zero point of mesurement terminl is displyed nd the djusted is sved in INL utomticlly. If zero djustment rnge is exceeded, the error[over] flshes twice nd then move to, mintining previous setting. Initiliztion Error disply HHHH LLLL D-HH D-LL F-HH PF-H PF-L + + for over 5 sec. INIT NO YE 4NN-DV/V 4NN-D/ Description Flshes when mesured input is exceeded the mx. llowle input (+110%) Flshes when mesured input is exceeded the min. llowle input (minus input ON: -110%, : -10%) Flshes when disply input is exceeded mx. disply rnge (9999) Flshes when disply input is exceeded min. disply rnge (-1999) Flshes when input frequency is exceeded the mx. mesured rnge (10kHz) nd disply rnge (9999) Flshes when power fctor disply to mesured input is over thn LG 0.50 Flshes when power fctor disply to mesured input is less thn LED Error is clered when the input is within mesurement rnge or disply rnge V TND Flshes twice in order nd it is initilized cycle dely[p 2 group: D1sT] In some pplictions the mesured input my fluctute which in turn cuses the disply to fluctute. y djusting the disply cycle dely function time t D1sT of prmeter 2 group, the opertor cn djust the disply time within rnge of 0.1 sec to 5 sec. For exmple, if the opertor sets the disply cycle time to 4.0 sec., the disply is displyed the verged input over 4 sec. in every 4 sec. onitoring mx./min. disply [P 0 group: hpek/lpek, P 2 group: PEkT] It monitors x./in. of disply sed on current disply nd then disply the dt in hpek, lpek of prmeter 0 group. et dely time (0 to 30 sec.) in PEkT mode of prmeter 2 group in order to void cused y initil overcurrent or over voltge, when monitoring the pek. Dely time is 0 to 30 sec. nd it strts to monitor the pek fter set time. When, keys re pressed t hpek, lpek mode of prmeter 0 group, it will e initilized. hpek, lpek prmeters is not displyed when monitoring dely time [PEkT] of prmeter 2 group is set s 00 sec.[00 ]. L-10

7 mll ulti Pnel eter Error correction[p 1 group: INH / INL] It corrects disply error of mesurement input. INL: -99 to 99 (djust devition of low-limit ), INH: to (correct grdient of high-limit ) = (mesured INH) + INL E.g.) When the mesured rnge is 0 to 500V, nd the disply rnge is 0 to If the low disply is!2 to 0V input, set -12 s INL to disply 0.0 y djusting offset of the low-limit. The disply to 500V mesured input vries y djusting the offset of low-limit. If this disply is 50!0, clculte 500.0/501.0 (desired disply /the disply ), nd set the )998 correction s the INH to disply 50)0 y djusting grdient of high-limit. The offset correction rnge of INL is within -99 to 99 for D -0, D -1 digit regrdless of deciml point position [DOT]. High limit error correction function is ville s Grdient correction function nd low limit error correction function is ville s Zero djustment function. Grdient correction[p 1 group: INH ] This function is to djust grdient of stndrd disply or scle for the input within the mesured input rnge. y djusting grdient, it is ville s High limit error correction function. s the elow (figure 1), in cse of disply grdient 1 for the mesured input 100V, this function is to djust disply y djusting the grdient s 1.5 times or 0.5 times. et rnge: to 9.999, Fctory defult: (unit: multiply) E.g. 1) Grdient djustment 1When the mesured input is 100.0V in order to disply 15)0, set grdient correction set [INH] s!500. This is lso pplied for minus input. When the mesured input is V, it displys -15)0. 2When the mesured input is V in order to disply -5)0, set grdient correction set [INH] s )500. This is lso pplied for plus input. When the mesured input is 100.0V, it displys 5)0. INH Note 1!500 2 )500 hded prt of Figure 1 is not displyed for the elow cses. C input model DC input model nd minus input[ 1NU] is set s. DC current input model nd rnge [ IN-R] is set s V 15)0 10)0 5)0-5)0 `0)0 `5)0 100V INH:!500 INH:!000 INH: )500 E.g. 2) scle setting [L-C/H-C]nd grdient djustment [INH] (C input) 1When the mesured input C 2.000V t the input rnge C 0 to 5.000V nd it displys %000, set deciml point position [DOT] s )000 efore setting the scle. 2When the mesured input is C 2.000V in order to disply %000, should e displyed when mx. input is 5.000V. However, it cnnot set ecuse the mx. set is et s Grdient correction set [INH] High scle [H-C] = 12,500 s the following tle. 3fter this setting is finished, it displys %000 when the mesured input is 2.000V. H-C L-C INH Note Unville to set ecuse mx. set of H-C is ( In this cse, ny setting methods disply the sme disply. for mesured input 2.000V 5.000V E.g. 3) scle setting [L-C/H-C] nd grdient djustment [INH] (DC minus input) 1When the mesured input DC -40m t the input rnge DC to 100.0m nd it displys `6)0, set deciml point position[dot] s )000 efore setting the scle. 2When the mesured input is DC -40m in order to disply `6)0, should e displyed when min. input is m. However, it cnnot set ecuse the min. set is et s grdient correction set [INH] low scle [L-C] = s the following tle. et high-limit scle s (- (L-C)). If high scle is set t first, set low scle s (- (H-C)). 3fter this setting is finished, it displys `6)0 when the mesured input is DC-40.0m. H-C L-C INH Note Unville to set ecuse mx. set of L-C is `9 ( In this cse, ny setting methods disply the sme disply () () Door/re Rotry ockets Temperture Rs / Power Pnel eters () Tcho / peed / Pulse eters ensor witching ode Power upplies tepper otors & Grphic/ Pnels () oftwre (Figure 1) for mesured input L-11

8 4NN eries Power fctor (PF) disply [P 1 group: H-RG/ L-RG] This function displys LED nd LG y nlog output signl from the power fctor trnsducer. It is ville to ccept severl outputs of the power fctor trnsducer y high-limit[h-rg]/low-limit[l-rg] nlog output setting in the power fctor trnsducer. Power fctor is displyed s cosø (LED) to 1.00 to 0.50 (LG). LED is when current phse leds voltge phse, LG is when current phse lgs ehind voltge phse. LED nd LG re invlid power. et rnge: From min. to mx. selected from mesurement input[in-r] E.g.) When setting 200V in IN-R, H-RG nd L-RG re ville to set from `9 (9 to 20)0. When setting 10V, H-RG nd L-RG re ville to set from `)00 to1)00. ( H-RG > L-RG) <Fctory defult> vlue odel cosø H-RG L-RG LED LG 1 4NN-DV NN-D %00 -%00 Power fctor disply is only 0.5 for DC mesurement input model. L-RG (H-RG)+ (L-RG) H-RG 2 E.g. 1) When the output of the power fctor trnsducer is DC 4-20m, 1Connect the output to the input terminl 5 (+), 7 (-) of this unit, then set input rnge[in-r] s When setting the input rnge s 4-20, L-RG is set s $00 nd H-RG is set s 2)00 utomticlly. L-RG nd H-RG is for the setting of the power fctor trnsducer output. 3If mesured input is 4m, it displys -)50. For 12m mesured input, it displys!00 nd for 20m, it displys )50. E.g. 2) When the output of the power fctor trnsducer is DC1-5V, 1Connect the output to the input terminl 5 (+), 7 (-) of this unit, then set the input rnge [IN-R] s 10V. 2elect minus input disply function [INU] s not to disply minus. 3et H-RG s %00 nd L-RG s!00 for the output of the power fctor trnsducer. 4If mesured input is 1V, it displys -)50. For 3V mesured input, it displys!00 nd for 5V, it displys )50. x. output V in. set V 3V 5V E.g. 3) When LED is smller thn -0.90, LG is smller thn 0.90, nd is used, 1et OU!T s HL t prmeter 2 group. 2et OU!H s )90 nd OU!L s -)90 t prmeter 0 group. OU@T is lso sme setting s OU!T. Output mode OU!H OU!L HL LG LED Hysteresis Hysteresis Output scle [P 1 group: H-C / L-C] This function is to disply setting (-1999 to 9999) of prticulr High/Low-limit in order to disply High/Low-limit of mesurement input. If mesurement inputs re '' nd '' nd prticulr s re '' nd '', it will disply =, = s elow grphs. In cse of DC Volt/mpere input model (4NN-D - ) nd using inus input, they re displyed. scle function is le to chnge disply for min./mx. mesured input y setting high limit scle H-C, nd low limit scle L-C in prmeter 1 group. E.g.) High limit scle nd low limit scle setting (input rnge = 0 to 10V) L-C: )00 H-C: %00, 1)00, 1%00, `)00 L-C: 1)00 H-C: `)00 1%00 1%00 1)00 1)00 %00 %00 L-C: -%00 H-C: %00 1%00 1)00 % V 0 10V 0 `)00 `)00 `)00 10V When chnging mesured input, high limit scle nd low limit scle re utomticlly chnged s the defult disply rnge of the chnged mesured input. 0.5 LED LG L-12

9 mll ulti Pnel eter Preset output mode [P 2 group: OU!T/OU@T] ode Output mode Opertion () No output No output () HI LO.H.L Hysteresis Period ON : OU!H Period : OU!H- HYs1 Period ON : OU!L Period : OU!L+ HYs1 Door/re HL.H.L Period ON : OU!L or OU!H Period : OU!L+ HYs1 or OU!H- HYs1 Rotry ockets HL-G.H.L Period ON : OU!L or OU!H Period : OU!H- HYs1 or OU!H+ HYs1 et output mode seprtely for ech /OUT2. /OUT2 re operted individully depending on output opertion mode. etting mode of prmeter group 0 is displyed depending on output opertion mode. GO outputs when the period oth /OUT2 re off. (NPN/PNP open collector output type) Temperture Rs / Power Pnel eters () Tcho / peed / Pulse eters ensor witching ode Power upplies tepper otors & Grphic/ Pnels () oftwre L-13