Services Unlimited, Inc./ Parts Guru 209 Walnut street, Lansdale, PA Phone: Fax:

Transcription

1 Services Unlimited, Inc./ Parts Guru 209 Walnut street, Lansdale, PA Phone: Fax: This Jura brew group refurbishing instruction guide does not suddenly make anyone an instant expert. Please make notes of your own for every step to separate the parts and wires. Tag the parts mark locations and even take pictures after every three or four steps. We cannot provide help for reassembling the brew group. om Refurbisjhing Jura Brew group is a precision work. Those who undertake this project have to be experienced in mechanical work. No responsibility is accepted for errors or damage to brew group or any injuries during repairs. op.p ar ts gu ru.c These instructions apply to all Jura brew groups. Although the drainage valve, located at the bottom of each group, may differ slightly based on the espresso machine model, the fundamental structure and design of the all the Jura brew groups are identical. sh 1. Jura brew group in the upright position. Ensure the espresso dispensing tube connector is removed completely. Also, disconnect the hot water silicone/teflon tube to the brew group from the thermo block. Remove the brew group from the machine and place it on an open table or area before disassembling it. Disassembling the brew group is the easy part. However, reassembling can be challenging for the first time users. We therefore recommend taking pictures or

2 WE HAVE CHANGED THE WAY BEANS ARE PACKED 4-OZ. BAGS - VACUUM SEALED WITH 1-WAY VALVE AIR & MOISTURE PROTECTED FRESH FROM ROASTER TO ESPRESSO MAKER. Exclusive Blend - Roasted just right - Precious Nectar remains inside the Beans Roasted Beans remain fresh in a vacuum sealed bag for two months. Open a 4-Oz vacuum sealed bag, & consume in 4-days until Beans are Fresh. NO REFRIGERATION. NO AIR-TIGHT JARS. NO BEAN-SITTING OPEN A BAG FRESH, JUST BEFORE BREWING (FRESH UNTIL CONSUMED) Why pay for Stale/Rancid beans & make bad tasting coffee? NO PROCRASTINATION NO COMPROMISES Four Blends to choose from. Try one today Discover what is Best Click Here to order Beans of your choice BUZZ 4-Oz. Bags MACHO Beans 4-Oz. Bags Espresso Bella - 100% Arabica 4-Oz. Bags BUZZ Decaf 4-Oz. Bags Bella 4-Oz. 55% Arabica- 45% Robusta Espresso Bella 4-Oz. Macho Beans 4-oz Caffe Bella Decaf 100% Arabica 90% Robusta- 10% Arabica 55% Arabica - 45% Robusta

3 While fixing the machine, make notes, take pictures & use sticky notes as you disassemble each component of the brew group. 2. Take the flat head screw driver and insert between the gap, as indicated above, to unlock the top portion of the brew group. Be gentle while removing it as the hinges might break off while removing. Remove from all 4 corners. For parts, repairs & Tech support, contact: Services Unlimited, Inc./ Parts Guru 209 Walnut street, Lansdale, PA sales@partsguru.com Online store: www.

4 3. Remove the top portion completely. Brew Group Side Cover 4. Remove the side covers. The side covers are snapped on to the brew group. Take the flat head screw driver, preferably, the sharpest edge, and insert between brew group side cover and brew group below the green marked area on the picture above. Slightly push the

5 flat head screw driver upward to remove the side cover. Be careful when removing the side cover for the red colored side as its hidden and can be challenging. Brew Group Drainage Valve 5. To detach the red marked side, insert the flat head screw driver to press the nose of the in the arrow direction and loosen it. Remove the side cover completely. Apply the same instructions to remove the side cover from the other side.

6 6. The brew group side railing can be removed easily after removing the side covers. 7. Remove the metal ring from both sides of the brew group. 8. Unscrew the brew group gear in the upward direction to completely remove it from the brew group spiral riser.

7 9. Slide out the top of the brew group plunger. 10. Push the lower piston lever to the left and then upward to detach the brew group drainage valve

8 11. The drainage valve should slide out easily 12. Removing the brew group shaft. Use the nose pliers to remove the C clip washers. Be careful as the E clip washer might jump off quickly as you remove it.

9 om gu ru.c sh op.p ar ts After removing E clip washers from both ends of the shaft, 13. simply pull out the shaft. 14. If the shaft is not easily removed, then use the flat surfaced tool to gently knock it out. Be careful as it can be little tricky. For parts, repairs & Tech support, contact: Services Unlimited, Inc./ Parts Guru 209 Walnut street, Lansdale, PA sales@partsguru.com Online store: www.

10 15. Remove the central mechanical part of the lower piston (brown), as shown above. 16. Remove the metal shaft completely from the center lower portion of the brew group.

11 17. Remove the lower piston 18. Remove the brewing cylinder For parts, repairs & Tech support, contact: Services Unlimited, Inc./ Parts Guru 209 Walnut street, Lansdale, PA sales@partsguru.com Online store: www.

12 19. Press the two arms of the gear drive carefully. Lower the gear drive and remove from the main brew group body. 20. Remove the old brew group piston o-ring using the flat head screw driver. Be sure to remove it gently. This lower gear is no sold separately. Be careful to not break it. Note the position before taking the lower piston out. Replace it in the same position, without turning it around.

13 21. Clean the o-ring groove on the piston. Lubricate the lower piston using the food grade lube. Replace the new piston o-ring. Apply lubricant cleanly around the piston and o-ring. This part is not sold separately. 22. Ensure the brew group piston o-ring is correctly replaced. For parts, repairs & Tech support, contact: Services Unlimited, Inc./ Parts Guru 209 Walnut street, Lansdale, PA sales@partsguru.com Online store: www.

14 23. Disassembly the brew group riser tube. 24. Slightly turn to release the riser tube and pull it upward

15 25. Replace the two o-rings located at the top and the bottom of the riser tube. Slightly lubricate it. Be sure to replace the crema/check valve (the small white piece indicated with red arrow) at the bottom of the spring correctly otherwise optimum espresso extraction can be compromised.

16 26. Replace the brew group cylinder o-ring. 27. Clean the piston o-ring groove and apply food grade lubricant. 28. Correctly replace the piston o-ring

17 29. Re-install the brew gear drive. Make sure there is no dirt in the transmission. Ensure the brew drive gears are clean. 30. Ensure the brew gear drive transmission is lined up correctly as displayed above.

18 31. Apply food grade lubricant to the inside of the brewing cylinder. 32. Apply the food grade lubricant to the piston o-ring.

19 33. Move the brewing chamber inside the brew group body. 34. Ensure both pieces slide together until it stops. For parts, repairs & Tech support, contact: Services Unlimited, Inc./ Parts Guru 209 Walnut street, Lansdale, PA sales@partsguru.com Online store: www.

20 35. Hold firmly and compress the gear drive and the brewing cylinder. 36. Attach the lower brewing plunger.

21 37. Loosen the right hand a little and with gentle pressure push the piston into the cylinder. 38. Place the brew group on the flat surface. Re-install the metal shaft.

22 39. Slightly lubricate the metal shaft when replacing it. 40. Replace both the metal rings on each side. Slightly bend the plastic tabs and metal rings while pushing. Ensure the metal rings are aligned correctly with the lower piston drive. For parts, repairs & Tech support, contact: Services Unlimited, Inc./ Parts Guru 209 Walnut street, Lansdale, PA sales@partsguru.com Online store: www.

23 41. Move the piston by hands few times to examine the movement of the lower brewing plunger. If unable to move it, then reassemble correctly. 42. Replace the c clip metal washers to secure the metal shaft.

24 43. Apply the food grade lubricant to the brew group piston o-ring if you didn t already before inserting into the brewing chamber. 44. Note the position of the upper piston riser tube inlet. Ensure its aligned correctly with the riser tube.

25 45. Slide the brewing piston down. 46. Replace the brew group ring.

26 47. Ensure the brew group ring thread is facing down when reinstalling it.

27 48. Bring the brew group ring down to 4-5 circular threads. 49. Apply the food grade lubricant to the brew group side channels.

28 50. Replace the metal ring 51. Repeat step 50 on the other side

29 52. Hold both sides together by hand. Ensure the lower piston is in the position indicated by the arrow. 53. Replace the drainage valve inlet seal

30 54. Replace the brew group drainage valve. Make sure that it fits into the groove from both sides. 55. Replace the brew group side panels.

31 56. Manually test the movement of the brew group. Always turn the brew group ring down completely and back all the way up to ensure smooth circular movement. 57. Bring the brew group to its home position as shown above. Ensure the position of the brew group ring. For parts, repairs & Tech support, contact: Services Unlimited, Inc./ Parts Guru 209 Walnut street, Lansdale, PA sales@partsguru.com Online store: www.

32 Gamea Revo Guru's Choice Fully Automatic Espresso maker. GURU'S CHOICE GAMEA MAIN FEATURES 1- Touch screen Technology to program & operate all functions. Buttons eliminated. 2- Solenoid valves dispense water & steam. Conventional water & steam valves eliminated. 3- Touch screen & function Icons eliminate knobs, On-Off switch & function buttons. 4- Brew group Easy access inside door for cleaning & maintenance. Unlike Jura machines. 5- Brew group water intake direct from Heat exchanger. Boiler valve eliminated. 6- Conical burr grinder feeds grinds direct into brew group. Doser & parts eliminated 7-15 Bar Pump. Valve control extracts espresso at 9 Bar. Coffee dispensed direct into cup 8- Initial warm up in 1.5 minutes. Pre-brewing & 2-Oz. Rinsing cycle, pours hotter coffee minutes non-use shuts off water & steam boiler. Prevents internal parts damage. 10- Removable Auto-frother or Manual (60 sec.) Milk steaming. Air adjustment knob. 11- Adjustable features: Coffee temperature 160F to 180F - Cup height 2.5" to 4.25" Coffee size adjustable from 30-ml. (1-Oz.) to 240-mm (8 Oz.). ESC icon display during each function to stop or interrupt anytime. Click Here for Gamea Black Gamea Revo has changed the way Classic espresso is made Click Here forgamea Revo Silver CLICK HERE for Gamea Demo Video. Dimensions: LxWxH= 18"x13.5"x15" Exclusive & Best buy in USA - Gamea Revo & Royal One Touch 120V Saeco Royal O.T. super automatic machine. Click Here 1- Easy access Brew group to clean- 2- Conical Burr Grinder 3- Removable Auto frother for steaming milk & easy cleaning. 4- User friendly display screen for Status & Program functions 5- One-step delivery of classic hotter Espresso, Americana, Cappuccino, Latte Macchiato at the push of button. Easy Tech-help & parts available, unlike for Jura machines. As Good As it Gets - Dimensions: Deep 18" x Wide 11" x High 15" Order one & UPGRADE your old & expensive to repair Jura, Breville, Gaggia Dimensions Royal O.T. - LxWxH= 18"x14.5"x15" Call: or inquiries: sales@partsguru.com

33 A New Star is Born. Aulika Top - One Touch High speed Combines aesthetics & Professional performance for Unrivalled performance Clean, rational design & unparalleled technology riginal Saeco lineage - Plumb option 4-Liter water tank; One Kilo beans container; Waste receptacles for 40-used coffee pucks & 1-Gallon drain tray. Double hydraulic circuit; two pumps; two Flowmeters & two boilers. Espresso dispensed in the cup immediately after steaming of Milk is complete (saves 20 seconds). Grinder with conical blades - (better than flat disc burrs). All these characteristics make this machine perfect for families, Offices, Catering, Rentals for Weddings, Graduation & other celebrations, Corporate Dining, Hotel Conference event, Hotel Lobies, Meeting rooms, & food service, Cafeterias, Restaurants, Pizza stores, or other locations. AuLika TOP High Speed One Touch is 10 Times Better Than JURA GIGA-5 (UL listed. ). Be the First proud Owner of an AuLika Top - CLICK HERE to watch Demo Video AuLika Top - One Touch High Speed model delivers a wide range of coffee-based and fresh-milk-based beverages, as well as hot water and steam. The wide graphic display can manage both icons and text messages in several languages. The interface is equipped with 8 direct selection keys that make the machine easy to use and program. For more information, availability & price & us: sales@partsguru.com

34 JURA DRAIN VALVE REPAIR This document has been translated fro Russian to English. Please use it for illustration and make your own notes at every one or two steps. A: 2 x O-rings B: 1 x O-ring C: 2 x U-gaskets B Services Unlimited, Inc./ Parats Guru 209 Walnut street, Lansdale, PA Phone: Fax: sales@partsguru.com

35 .. ull the hairpin clip out. Remove the water inlet connector

36 Push the spring in as shown by arrow.

37 Follow the arrow display above Follow the disassembly as shown above.

38 Follow the disassembly as shown above. Pulling the Lip gasket seal. Replace the gasket as shown above.

39 Pry out the O-ring. Note the size of O-ring is different from the other O-rings.

40 Lip gasket Lip gasket pushed in place

41 Push gasket enough to leave the notch free This closing piece has male notch to fit in the female notch and prevent rotation.

42 .Follow the arrows for direction to seat the lip gasket and the pressure spring. Apply thin layer of lube. The smaller O-ring slides at the tip of water connection plastic tube. Wet the tube tip with lube.

43 Other small O-ring slides on the side of the outlet tube A thin film of lube should be applied to all O-rings and gasket before installing each.

44 Final assembled view of the drain valve.

45 Replace the drain valve in the Drain valve housing as shown above. Lock the drain valve with hairpin clip. Replace it in the brew group bottom.

46 RP13343 Impressa C9 pianoblack (CH) 654 Edition: 27/10/09 (9) Brew unit For parts, repairs & Tech support, contact: Services Unlimited, Inc./ Parts Guru 209 Walnut street, Lansdale, PA sales@partsguru.com Online store: www. Page 18 / 19