TM_EN Part No.: 1764154_03 TECHNICAL MANUAL
CONTENT CONTENT... 2 GENERAL... 3 Facts & weight...3 Dimension sketch...4 CLEANING PROGRAM... 5 Clean mixer...5 Clean valves...6 Clean grinder...7 Grinder EK-7...8 Periodic maintenance...8 Safety...8 Monthly maintenance...9 Basic adjustment of the grinding finess... 10 ERROR CODE DESCRIPTION... 11 FLOW CHARTS... 13 Water system CQube series... 13 ELECTRICAL SCHEMATICS... 14 High current 3 x 400VAC 1N 6600W... 14 High current 3 x 230VAC 4400W... 15 High current 230VAC 1N 2200W... 16 IO-board outputs... 17 EXPLODED VIEW... 18 Machine... 18 Door... 20 Tank 5L... 22 Bean hopper... 24 Grinder EK 7... 25 SERVICE INTERVALS... 27 PROGRAMMING... 28 Activate programming with user card... 28 Clean machine... 28 Counters... 29 Beverage setup, Strength... 31 Beverage setup, Volume... 32 Beverage setup, Drink Settings... 33 Beverage setup, Recipe Bank... 34 Beverage setup, Enable Beverage... 35 Drink setup... 36 Some important information may appear in textboxes seen below IMPORTANT! INFO. CAUTION! INFO. More INFO. Note INFO. 2
GENERAL Facts & weight FACTS Built-in grinder Yes Drink options 9 Ingredient canister None Bean hoppers 2 Brewing mechanism Cleaning function by smart card Electronic temperature control Adjustable coffee strength Illumination of cup during brewing Base cabinet: large grounds container Energy saving mode Height, Width, Depth Tank volume Power supply Cold water connection Water purification filter None Yes Yes Yes Yes None Yes 865, 290, 532mm 5 Litres 380VAC, 50/60Hz/6600W ½ External thread Option MODEL/NAME WEIGHT 40kg 3
GENERAL Dimension sketch B C A D E F Model A B C D E F 865mm 290mm 532mm 160mm 200mm 240mm 4
CLEANING PROGRAM Detailed cleaning instructions Clean mixer Cleaning means rinsing with water and rotating the whipper. A Cleaning of the mixing bowl should be performed once per day. Insert technical service card Step to Clean Machine Enter or press Cleaning Hot Key appears on the display Clean Machine Open the machine door. Put a container that holds at least 0.5 litres under the outlet for hot drinks. button on the cleaning panel. (See fig. A) The machine will now clean the mixing bowl for 5 seconds. Close the door and remove technical service card to return to normal mode. Note Repeat the cleaning procedures 2-3 times to get a better cleaning effect. 5
CLEANING PROGRAM Detailed cleaning instructions Clean valves A Cleaning entails that the valves knock off any lime scale and other particles that may get stuck in the cylinders and flushing them with water. Insert technical service card Step to Clean Machine Enter or press Cleaning Hot Key appears on the display Clean Machine Open the machine door. Put a container that holds at least 0.5 litres under the outlet for hot drinks. button on the cleaning panel. (See fig. A) The machine will now clean the dispenser valves for 5 seconds. Close the door and remove technical service card to return to normal mode. Note Repeat the cleaning procedures 2-3 times to get a better cleaning effect. 6
CLEANING PROGRAM Detailed cleaning instructions Clean grinder Tips: Keep a cup under the grinder outlet during the cleaning process. A B Cleaning with grindz cleaning tablets, Every month (Product No. E1001001) Insert technical service card Step to Clean Machine Enter or press Cleaning Hot Key appears on the display Clean Machine Open the machine door. Remove the brewer from its position and close bean stop in bottom of the bean hopper. Start grinder by pressing button (Grinder 1), this is a Push and Hold function, the grinder will run as long as the button is pressed. (See fig. A) Run grinder until no powder comes out of the grinder outlet, approx 10sec. Remove the bean hopper and pour out the remaining coffee beans. Reassemble bean hopper and fill with a cap GRINDZ cleaning tablets and reopen bean stop. (See fig.c) Start the grinder again by pressing button approx 10sec. Run until no more cleaning powder come out of the grinder. Refill the bean hopper with fresh coffee beans. Reassemble the brewing mechanism. Close the door and remove technical service card to return to normal mode. Make one cup of brew coffee and throw it away. fig.c Note If machine have two grinders, follow same procedure but use button instead (Grinder 2) (See fig. B) Grinder 1= left grinder Grinder 2= right grinder 7
MAINTENANCE AND CARE Grinder EK-7 Bean Hopper Bean Stop Grinder Grinder outlet Grinder Adjustment Wheel Fixation Screw Periodic maintenance Each month: clean outlet, grinding house and grinding discs. Monthly cleaning of grinder using GRINDZ cleaning tablets (item no. E1001001). Safety Please read and observe the following service instructions carefully. Non-observance can result in damage to the grinder as well as in healththreatening risks for the user. All installations shall been done by an qualified personnel. Symbols Safety instruction: In case of non-observance, extreme risk of accidents exists. General instruction: In case of non-observance, the device can become damaged or optimum operation not be guaranteed. Safety instructions The grinder is only allowed to be used to grind whole coffee beans. Ground coffee is never allowed to be filled into the input-shaft. Do not carry out any modifications or changes on the grinder. In case for non-observance, the manufacturer shall be liable for resulting damain no case whatsoever. Never put your fingers or objects into the rotating grinding mechanism inside the inputshaft.the grinder must not be operated when turning parts are accessible! Make sure, that the power cannot be turned on when working on the built-in grinder! In order to avoid damages, do not use power tools or cordless electric screwdrivers for any work on the grinder. 8
MAINTENANCE AND CARE Grinder EK-7 Monthly maintenance Approximately every month the grinder housing and spout should be inspected for coffee residues and obvious damages. A Fig.1 Fig.2 Proceed as follows: Remove bean container. Remove all coffee residues from the spout and the grinder housing by grinding through all coffee beans and using a vacuum cleaner to remove all residues. Remove the two Phillips screws (A, See fig.1) on the side of grinder housing lid. Carefully detach the grinding housing. Fig.1 Note its position for correct reassembly. Do not alter the adjustment of the grinding discs. Clean the inside of the grinder housing with a soft brush. (See fig.2) When reassembling the grinder housing, again check for the correct position and do not alter the grind adjustment of the discs. Fasten the two Phillips screws. 9
MAINTENANCE AND CARE Grinder EK-7 Basic adjustment of the grinding finess The grinder adjustment can be easily reached through the space between the bean hoppers, before adjusting loosen the fixation screw in front of the adjuster wheel to be able to rotate it. To adjust the coarseness for left grinder, rotate the adjuster wheel towards you for coarser grinding. For finer grinding rotate the wheel away from you. To adjust the coarseness for right grinder, rotate the adjuster wheel towards you for finer grinding. For coarser grinding rotate the wheel away from you. Take into consideration that after the adjuster is moved, the effect is not immediate, it takes about 1 coffee cycle for the new coffee grounds to reach the outlet and into the brewer. So to test the new adjustment, observe the second coffee after the change. The finer the grinding, the slower the coffee will come out, and longer time will be needed for the extraction of the espresso and vice versa. CCW for Coarser Grinding CW for Finer Grinding Fig.3 10
ERROR CODE DESCRIPTION Overcurrent Group 1:1 = Brewing unit (0,95A limit) Espresso unit (1,5A limit) Group 1:2 = Other components (Fan, Valves, Relays Etc..) (1,5A limit) Group 1:3 = Mixer 1 (3,5A limit) Group 1:5 = Mixer 2 (3,5A limit) Group 2:1 = Milk pump (1,5A limit) ERROR: Water Supply ERROR: Tempsensor Message is shown if one of the software fuses have been trigged. Caused by a component using too much current (A). You can run each component in the Hardware Test menu and the message will show when you turn on the component that is using too much current. Message will show if the inlet valve has been open for more than 3 minutes and the machine still have not acquired correct water level. Action: Check that the water to the machine is turned on, Check the levelsensor, test function of the inlet valve in Expert Settings Message will show if the NTC sensor is broken or is out of range of its resistance curve, also if cables have loosened from its connectors. Action: Replace NTC sensor, check cable connection on the NTC and PCB board. ERROR: Levelpins Message will show if the cables to the water level high & low have been connected to the wrong levelpin. Action: Swap cables to the levelsensor ERROR: Check Heater Message will show if the machine have not reached working temperature within 14 minutes from startup. Action: Check Overheating protection, cables to the element, solid state relay, signal from IO-board to solid state when you know the machine should heat, you can also force the element to run in Expert Settings. ERROR:Brewer C.Door E Message will show when you interrupt a brewing cycle, eg. open the door when the machine is producing coffee. The machine needs to reach home-position before producing new drink. Action: E, check door sensor, brewmec sensor Clean brewfilter Message will show if the brewer motor uses more than 0,95A for filter brewer, 1.5A for espresso brewer. Action: Check brewfilter if clogged, brew chamber is mounted in wrong position, brewer motor is broken. 11
ERROR CODE DESCRIPTION Peripheral Hardware Error This message will appear if you have loaded a faulty recipe into the machine, the IO-Board is broken and does not get connection with the UcMerisc board. Usually this message appears if you eg. have loaded a standard recipe into a machine using pay system. Make sure you are using the right recipe and reload. Memory Error: Reload Recipes There is no recipe loaded on the UcMersic board. Transfer of the recipes have been interrupted and not completed in UcLoader. Memory on the UcMersic board is broken. Fatal Error Contact Service Multiple Overcurrent messages at the same time, or shortcut on the IO-Board, try to run components in Hardware Test and locate faulty components, replace the IO-Board if no one is found. Smartcard Error: Unknown Card The smartcard is not programmed, chip on the smartcard is damaged, card reader is broken or broken cable between card reader and UcMerisc board. Action: Insert and remove the card repeatedly, if the message is shown every time, try another card. If the error remains replace the card reader. Smartcard Error Wrong Pincode Chip on the smart card have been damaged, replace card. Pay Error Type XXX IO-Pay board is reporting error from the payment device, check coinchanger or cashflow device. 12
FLOW CHARTS Water system CQube series Inlet Tank 96 0 C Level pin Heater elements Outlet 1 Mixer Decanter Outlet 2 Tea water Tea Cup Overfill NTC Waste bin Note Cold water unit is not a standard feature in the machine it s only an option. 13
ELECTRICAL SCHEMATICS High current 3 x 400VAC 1N 6600W 14
ELECTRICAL SCHEMATICS High current 3 x 230VAC 4400W L3 L2 L1 L1 L1 L3 L2 15
ELECTRICAL SCHEMATICS High current 230VAC 1N 2200W 16
ELECTRICAL SCHEMATICS IO-board outputs J3 Neltron 5566, 16POL (OUTPUTS 24V) J1 Neltron 5566, 22POL (OUTPUTS 24V) 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 HOT WATER OUT (TEA) HOT WATER IN (inlet tank) 1 3 5 7 2 4 6 8 5V GND X RESET ADR IN WATER LEVEL HIGH DRIP TRAY DOOR HOT WATER SWITCH TEMP. 1 3 5 7 9 11 13 15 17 19 21 2 4 6 8 10 12 14 16 18 20 22 HOT WATER MIXER FAN HEATER TANK GRINDER 2 GRINDER 1 2 4 6 8 10 12 14 16 18 20 22 24 26 1 3 5 7 9 11 13 15 17 19 21 23 25 1 3 5 7 2 4 6 8 Yellow green Blue Black GND 24V 1 3 2 4 24V RX TX ADR OUT L N GND -V -V +V +V WATER LEVEL LOW J6 J5 J2 J4 BOXHEAD 24POL (INPUTS) Fuse 1 Fuse 2 Fuse 3 OUT 17 OUT 18 OUT 15 OUT 16 OUT 13 OUT 14 IN 19 IN 20 OUT 8 OUT 7 OUT 10 OUT 9 OUT 16 OUT 15 OUT 2 OUT 1 IN 21 IN 22 IN 23 IN 24 IN 3 IN 4 IN 2 IN 1 230 AC to 24 VDC 17
EXPLODED VIEW Machine Drawing 01 02 03 04 06 05 07 08 34 09 10 12 20 13 21 15 11 26 22 27 17 14 16 28 18 29 19 24 25 30 41 31 18 32 33 23 35 36 37 38 39 40
EXPLODED VIEW Machine Spare parts list POS. PCS Part No. Description 01 1 160841 Microswitch or 710070 with holder 02 1 7160003 Bean hopper left 03 1 7160004 Bean hopper right 04 1 1604384 Fuse 5AT 5x20 05 1 1604111 PCB MAIN BOARD IO-TE 06 1 1031652 Power supply 150W 07 1 260755 Water tank 5L 3-phase complete 08 1 1604151 Centrifugal fan 24V 0.24A 09 3 160536 Gasket rubber NBR(Rubber trp 30.0) 10 1 160549 Connector FV122/B 11 1 1604174 Adjustable steam tube, white 12 2 1608281 Magnet 39x13x6 13 1 1604757 Grinder EK-7 left 14 1 1604758 Grinder EK-7 right 15 1 1264098 Grinder outlet left 16 1 1264099 Grinder outlet right 17 1 120497 Bulkhead adapter 18 1 120487 Steam trap 19 1 1201411 Angle outlet 20 1 120465 Rubber lead-in TPG 20.5 21 1 1031804 Chassis connector 22 1 1031302 Tea water pipe 23 1 1105358 Waste bin 24 1 1605651 PG complete (PG16) 25 1 160801-04 Rocket switch single(orange) 26 1 1402581 Screw M4X10 black plastic top 27 1 252109 Drain panel 28 1 1602413 Relay 24V 29 3 1604203/1604201 Solid state 25A 30 3 1206581 Seal solid state 31 1 1264114 Outlet pipe insert 32 1 1364023 Outlet pipe prezzo 33 2 1402163 Screw M4x8 34 1 1660005 Grinder AC to DC PCB 35 1 1206371 Valve inlet 2.5L /min 24V 36 4 120316 Adjustable foot 37 1 1505042 Inlet hose 38 1 1605241 Power cord 3-phase 1.8m 39 1 1264161 Gasket DIA23.5mm x 15mm D3mm 40 1 1264160 Gasket DIA18mm x 9mm D2mm 41 1 2760094 Gasket set for inlet hose 19
EXPLODED VIEW Door Drawing 01 02 10 11 03 04 05 07 06 08 12 13 14 15 16 17 18 35 31 19 20 09 34 33 32 21 22 23 24 25 26 27 28 29 30 20
EXPLODED VIEW Door Spare parts list POS. PCS Part No. Description 01 2 1301940 Aluminum corner profile 02 1 1364027 Door key 03 1 1660014 Fan 24V 60x60x10mm 04 1 1105542 Door lid Cqube S 05 1 180115 Pin for door instant 06 1 1603910 Clean sticker 07 1 1606745D Harness LED CQubes 08 1 260487 Door outlet cover 09 1 710556 PCB UC and display 2x16 complete 10 1 1801143 Lock 103A-17 11 1 256097 Lock latch 12 1 1301918 Aluminum center profile 13 2 1105544 Window profile Cqube S 14 1 1301945 Aluminum side profile 15 1 1361720 Aluminum side profile 16 1 1105550 Display list 17 1 1665047 Membrance swtich 18 1 260561 Display modul panel 19 1 1602697 Card reader 20 1 1505035 Card reader front rubber 21 1 1105532 Chrome ring 22 2 1264109 Cup tray prezzo 23 1 1105534 Outlet driptray 24 1 1105543 Drip tray extension Cqube S 25 1 260613 LED lamp bracket 26 1 1665063 Prezzo logo sticker 27 1 1264109 Cup tray replacement 28 1 1665063 Prezzo sticker mat 29 1 1665061 Membrane switch sticker 30 1 1301938 Aluminum hinge profile 31 1 1604119 Battery CR 1220 3V 32 4 1604113 Spacer for UC merisc 33 1 1604117 PCB display board UC-meric 34 1 1604122 Display 2x16 35 4 1203416 Fastener for circuit board 21
EXPLODED VIEW Tank 5L Drawing 01 02 07 03 04 05 06 08 09 10 25 18 19 20 11 12 26 21 13 27 28 22 23 14 15 24 16 29 17 30 31 32 33 22
EXPLODED VIEW Tank 5L Spare parts list POS. PCS Part No. Description 01 1 1401101 Nut M3 SS A2 02 1 1461008 Spring washer M3 03 1 1364026 Sensor short 60mm 04 1 1205301 Sensor long 90 mm 05 1 1605362 Double seal level sensor 06 1 1666013 Harness water level sensor 07 1 1660057 Valve coil 24V DC black 08 1 1660058 Valve metal plunger and spring 09 1 1501193 valve silicone plunger 10 1 1660060 Valve upper body 11 1 1206452 O-ring adjustment screw 12 1 1206451 Valve body o-ring 13 1 1660062 Valve lower body 14 1 260851 SS clamp holder left 15 1 260852 SS clamp holder right 16 1 220220 High limit switch 17 1 1561014 Inlet pipe tank 18 1 250433 Tank washer 19 1 1402003 Screw M4 x 16mm 20 1 260144 Tank lid fixture 21 1 1206507 Fiber washer 22 1 1561012 Seal gasket tank 23 1 1206505 Gasket for Hl switch ber 16.8x12.4 24 1 1601311 Element 2200W/230V with SS nuts 25 1 1605363 Silicone plug 26 1 1561015 Overflow pipe 27 2 160538-03 Plug for water outlet 28 3 1561010 Seal for outlet valve 29 1 1505010 Tube silicone 8-12mm 30 1 1206290 Outlet valve black 24V 31 1 1604135 NTC thermistor 32 1 1605361 Seal for NTC 33 1 1201295 Insulation 5L tanks (black 15mm) 23
EXPLODED VIEW Bean hopper Drawing 03 04 05 01 02 06 08 07 13 09 10 11 12 Spare parts list POS. PCS Part No. Description 01 1 1105536 Lid bean hopper CQUBE S 02 1 1105537 Bean hopper top lid CQUBE S 03 1 1105547 Bean hopper back panel 04 1 1608281 Magnet 39x13x6mm 05 1 1105558 Magnet lid 06 1 1105538 Front bean hopper small A (Left) 07 1 1105539 Front bean hopper small B (Right) 08 1 1105535 Bean hopper back CQube S 09 1 120224 Spring for bean stop 10 1 260336 Bean stopper 11 2 1461013 Washer M4 A2 Flat DIN 15A 12 1 1461005 Screw M4x40 A2 PH recessa pan 13 1 1264083 Sealing Rubber for Bean Hopper 24
EXPLODED VIEW Grinder EK 7 Drawing 04 01 05 02 06 03 07 08 09 10 11 25
EXPLODED VIEW Grinder EK 7 Spare parts list POS. PCS Part No. Description 01 1 1965003 Housing EK-7 02 1 1965005 Grinding disc set EK-7 03 1 1965006 Rotating burr carrier EK-7 04 1 1965004 Standard outlet EK-7 05 1 1264097 Outlet holder for EK-7 grinder 06 1 1264098 Grinder outlet left 07 1 1264099 Grinder outlet right 08 3 1965007 Grinder belt 420t EK-7 09 1 1965008 Adjustment bar EK-7 10 2 260457 Adjustable shaft 11 2 1264033 Adjustable wheel EK-7 26
SERVICE INTERVALS Main Components Parts Part No. Months 3 6 9 12 Boiler Outlet Valve Membrane 1660059 Check Replace Sealing 1561010 Check Replace Levelsensor Levelpins 1205302 Clean Clean Sealing 1205301 Check Replace NTC Sensor 711000 Check Check Sealing 1605361 Check Check Grinders Grinder Discs Clean Clean Clean Clean Ventilation Fan Mixer Ventilation tube Clean Clean 27
PROGRAMMING Activate programming with user card Insert user card in the card reader (A) The display shows: Service Menu Clean Machine A Service Menu Counters Service Menu Beverage Setup button to scroll between the different menus Clean machine Open the door. ENTER on the cleaning panel inside the door. Choose button X for each cleaning. Cleaning hot key See the pages for cleaning programs in order to perform cleaning. 4 Clean Mixer 5 Clean Valves Enter 8 Clean Grinder 1 9 Clean Grinder 2 28
PROGRAMMING Counters See the counter of each drink or total counters for all drinks. It s also possible to reset the drink counters. Service Menu Counters Service Menu Counters Counters Beverages Beverage Counters Per Beverage Drink 1 served xxx to go forward in the menu Drink 2 served xxx Beverage Counter Total Served Total Beverages Served xxx Beverage Counter Master Total Master Total Served xxx Beverage Counter Clear Counters Hold Enter to Clear Counters Hold ENTER key for 3 seconds to go back in the menu Counters Cleared Back 29
PROGRAMMING Counters See the number of times cleaning has been performed or reset the water filter counter. Service Menu Counters Counters Clean Counter Clean Counter Brewer xxx to go forward in the menu Clean Counter Total xxx to go back in the menu Counters Water Filter Water Filter Reset Filter Reset? NO/YES Months Left 6 Standard=6 months to go forward in the menu Water Filter Interval 6 Water Filter Interval 1-12 to go back in the menu 30
PROGRAMMING Beverage setup, Strength Change strength of the different drinks. If you are using a recipe with both grinders, Strenght will only change the grinding time for the left grinder. Service Menu Beverage Setup Beverage Setup Strength To go forward in menu. STRENGTH Drink 1 Strength xx% To go forward in menu. Choose another drink. Drink 2 Strength xx% Drink 3 Strength xx% Drink 4 Strength xx% Drink 5 Strength xx% Factory default value Drink 1 Strength xx%+0 Change the value of a drink, or Confirm the new setting by pressing the Increase or reduce value in % To step backwards in the Menu. Drink 6 Strength xx% Drink 7 Strength xx% Drink 8 Strength xx% Drink 9 Strength xx% Drink 10 Strength xx% Note To see the standard settings, please go to page 24. 31
PROGRAMMING Beverage setup, Volume Change volume of the different drinks. Service Menu Beverage Setup Beverage Setup Volume To go forward in menu. VOLUME Drink 1 Volume xx ml To go forward in menu. Choose another drink. Factory default value Drink 1 Volume xx ml Increase or reduce value in ml Drink 2 Volume xx ml Drink 3 Volume xx ml Drink 4 Volume xx ml Drink 5 Volume xx ml Change the value of a drink, or Confirm the new setting by pressing the To step backwards in the Menu. Drink 6 Volume xx ml Drink 7 Volume xx ml Drink 8 Volume xx ml Drink 9 Volume xx ml Drink 10 Volume xx ml Note To see the standard settings, please go to page 24. 32
PROGRAMMING Beverage setup, Drink Settings Change grinding time for right grinder if you are using a recipe with both grinders. Service Menu Beverage Setup Beverage Setup Drink Settings DRINK SETTINGS To go forward in menu. Choose another drink. Drink 1 Factory default value Drink 1 CoffeeBea xx%+0 Increase or reduce value in % Drink 2 Drink 3 Drink 4 Drink 5 Change the value of a drink, or Confirm the new setting by pressing the To step backwards in the Menu. Drink 6 Drink 7 Drink 8 Drink 9 Drink 10 Note To see the standard settings, please go to page 24. 33
PROGRAMMING Beverage setup, Recipe Bank Change recipe on different buttons. You can find all recipes and drink codes on page 24. Service Menu Beverage Setup Beverage Setup Recipe Bank Key#ZZ R#XXX <Drink 1 name> Choose which drink key (key #ZZ) that should be related to which recipe (R#XXX) in the recipe bank. Confirm with ENTER. Key#ZZ R#XXX <Drink 2 name> To go forward in menu. Choose which drink key (key #ZZ) that should be related to which recipe (R#XXX) in the recipe bank. Confirm with ENTER. 34
PROGRAMMING Beverage setup, Enable Beverage Enable or disable different drinks and buttons. Service Menu Beverage Setup Beverage Setup Enable Beverage ENABLE BEVERAGE Drink 1 Enable Bev ON To go forward in menu. Choose another drink. Drink 1 Enable Bev On-Off Drink 2 Drink 3 Drink 4 Drink 5 Change the value of a drink, or Confirm the new setting by pressing the To step backwards in the Menu. Drink 6 Drink 7 Drink 8 Drink 9 Drink 10 35
PROGRAMMING Drink setup Button RB Code DRINKS Grinder VOLUME BEANS Min Max Normal Min Max Normal % in machine 1 #R009 Small jug left Left 150ml 800ml 250ml 0g 60g 18.5g 31% 2 #R011 Medium jug left Left 150ml 1000ml 500ml 0g 70g 30g 43% 3 #R013 Large jug left Left 150ml 1500ml 750ml 0g 90g 45g 50% 4 #R015 Grand jug left Left 500ml 2000ml 1000ml 0g 120g 60g 50% 5 #R007 Hot water continous 6 7 8 9 #R010 Small jug right Right 150ml 800ml 250ml 0g 60g 18.5g 31% 10 #R012 Medium jug right Right 150ml 1000ml 500ml 0g 70g 30g 43% 11 #R014 Large jug right Right 150ml 1500ml 750ml 0g 90g 45g 50% 12 #R016 Grand jug right Right 500ml 2000ml 1000ml 0g 120g 60g 50% RB #R003 Dual small jug Dual 150ml 800ml 250ml 0g 35+35g 9+9g 26%+26% RB #R004 Dual medium Jug Dual 150ml 1000ml 500ml 0g 40+40g 15+15g 37%+37% RB #R005 Dual large jug Dual 150ml 1500ml 750ml 0g 50+50g 22.5+22.5g 45%+45% RB #R006 Dual grand jug Dual 500ml 2000ml 1000ml 0g 60+60g 30+30g 50%+50% RB #R008 Hot water Dosed 50ml 200ml 150ml 36
For the warranty to be valid the conditions for maintenance must have been followed according to our instructions, proper precaution has been made and warranty claim been issued without delay. The affected equipment may not be used during awaiting service if there is any risk that the damage or defect would worsen. The warranty will not cover consumption supplies such as glassware, normal maintenance such as cleaning of filters, contaminations in water, lime, incorrect voltages, pressure or adjustment of water amounts. The warranty will not cover damages of defects caused by incorrect handling and operation of the appliance. FOR SERVICE Please contact your dealer Your Dealer www.creminternational.com