Brew Group removal instructions for Jura C, E, and F series: Suitable for the following Jura Impressa models JURA all IMPRESSA E, F, and C: E-Line: E10 * E25 * E30 * E40 * E45 * E5 * E50 * E55 * E60 * E65 * E70 * E74 * E75 * E80 * E85 F-Line: F9 * F90 * F70 * F5 * F50 C-Line: C5 1. Disclaimer: This service manual describes the expansion and overhaul of the brewing unit of Jura E50. Services Unlimited Inc.Parts Guru is NOT responsible for any errors in understanding and repairs or use of these instructions by inexperienced users. 2. Safety Warning: A coffee machine uses water, heat, steam and electricity. Allow the machine to cool before repairing or servicing the machine. The thermo couples need up to 5 hours to cool down. Please work carefully and wisely. Read the instructions thoroughly before taking on repairs. Services Unlimited Inc./Parts Guru shall NOT be responsible for any damages to the property or any personal injuries while repairing the machine. We sell only the Best espresso machines. Guru's Choice: Jura XJ9, Jura Impressa X9 NSF; & Royal One Touch We offer after sale service, parts, repairs & Tech support, like nowhere else For Homes, Businesses, Restaurants, Corporate dining, Rentals, Catering & more For routine maintenance of espresso machine: CLICK HERE for Espresso maintenance DOs & DON'Ts
Required Tools: Normal screwdriver, Phillips screwdriver, oval head wrench, pliers, Torx TX20 and TX15 Torx (depending on model). Brew group C,E,F,S series Jura grinder temperature sensor Magnet valve 110V Click picture to order online. If the link is broken, it will open the Home page. If so, type the desription in Quick search to open the page.
For Jura parts, repairs & tech support, contact: Click Here to order parts online. If any link is broken, it will open the Home page. If so, type the name of part in Quick search to find it. Jura water tank outlet valve kit co Small gear brew drive motor Hose clamps set of three Brew group maintenance kit Complete grinder 120V DC Coffee outlet hose support Pa r ts E8 E9 Steam outlet G ur Oval head key u. Jura membrane regulator hair pin type m Membrane regulator Clamp type with 12" reinforced hose Thermostat L=115C Dial component frother complete Legis connetors Thermoblock Drip tray E Series Clearyl filter cartridge Brew group Piston Oring pair with lube Transformer for all models Step down 120V-9V Bullet tip nozzle Click on the part to order online. If the link is broken, it will open the Home page. If so, type name of part in the Quick search to access.
For Jura parts, repairs & tech support, contact: Dismantling the Machine 1. Unplug the machine. Remove the drip pans and water container. Empty the coffee bean hopper, so no coffee beans fall into the machine.
2. Use the oval head screw key to remove the oval head screws from the back of the machine. Rotate the key counterclockwise. 3. Unscrew the oval head screw gently without causing any damage to the machine. For Jura parts, repairs & tech support, contact:
4. Remove the upper screws using the phillips or Torx screw driver. Rotate counter clockwise 5. Remove the upper part completely carefully without damaging the side flaps
6. Remove the left side panel by gently sliding it backwards to disengage the tabs from the front panel. Once the tabs are unhooked, slowly remove the side panel. 7. Apply the same procedure to remove the right side panel as indicated in step 6. For Jura parts, repairs & tech support, contact:
8. Remove the bolt from the brew drive gear motor using the Torx 20 or Phillips screw driver (depending on the model). Be sure to use the correct tool to remove the screw. Using the wrong tool may worn out the grooves hence making it difficult to remove the screw. Jura Grinder key to unblock Ring & Cone Grinder burrs For Jura parts, repairs & tech support, contact:
9. Remove the hair pin clip from the heating cartridge valve on the right side of the machine using the screw driver or the pliers. 10. Pull down the transparent silicone hose from the heater valve. Be sure to remove the seal/o-ring at the end of the silicone hose. It often remains inside the valve and can be removed using the screw driver.
11. Remove the screw from the water tank seal cover on the left side of the machine. For Jura parts, repairs & tech support, contact:
12. Slide out the water tank seal assembly slowly. No need to remove the hose inside the assembly. 13. Cut the cable ties at the ground coffee funnel
14. You may remove the gound coffee funnel but it's not necessary. 15. Unsrew the three highlighted screws using the phillips or Torx screw driver. Do not remove any other screws that are attached to the brew group guide.
16. Slide out the brew group slowly. Ensure that infuser pipe out of the brew group to the coffee dispensing assembly is detached. For Jura parts, repairs & tech support, contact:
17. Slide up the brew unit guide 18. Detach the infuser connector mounted atop the brew group. Leave the infuser hose attached For Jura parts, repairs & tech support, contact:
19. Detach the coffee sweeper/scraper from the brew group. For Jura parts, repairs & tech support, contact:
20. Brew Group without the brew group guide and coffee scraper.