MY MILKY PRO www.martellocafe.ca ENGLISH: 1-22 FRENCH: 23-44 INSTRUCTION MANUAL MARTELLO My Milky Pro, Milk frother MODEL: BVMTMMP402-033, My Milky Pro
TABLE OF CONTENT EN Table of content...2 Important Safeguards... 3-6 Product Description...7 First Use... 8-9 Daily Use - Heating Milk...10-11 Daily Use - Frothing Cold Milk... 12-13 Daily Use - Frothing & Heating... 14-15 Cleaning... 16-17 Warranty...18-19 Recipes...20-21 2 MyMilky PRO
EN IMPORTANT SAFEGUARDS When using electrical appliance, basic safety precautions should always be followed to reduce the risk of fire, electric shock and/or injury to persons, including the following: 1. READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. 2. DO NOT touch hot surfaces. Use handles or knobs. 3. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquids. 4. Unplug unit from electrical outlet when not in use and before cleaning. Allow it to cool before putting on or taking off parts and before cleaning it. 5. DO NOT operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return this appliance only to the nearest Authorized MARTELLO Service Center for examination, repair or adjustment. 6. The use of accessory attachments not recommended for MARTELLO products may result in fire, electric shock or injury to persons. 7. DO NOT use outdoors or for commercial purposes. 8. DO NOT let cord hang over edge of table or countertop or touch hot surfaces. 9. DO NOT place this appliance on or near a hot gas or electric burner or in a heated oven. 10. Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control to off, then remove plug from wall outlet. MyMilky PRO 3
IMPORTANT SAFEGUARDS When using electrical aplliance, basic safety precautions should always be followed to reduce the risk of fire, electric shock and/or injury to persons, including the following: 11. DO NOT use appliance for anything other than its intended use. 12. Use on a hard, flat level surface only, to avoid interruption of airflow underneath the appliance. 13. Always be sure to install the milk container securely back on the unit with its lid closed after filling with milk and before turning appliance on. 14. DO NOT remove the milk container until unit is turned off. 15. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given permission or proper instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they DO NOT play with the appliance. 16. Scalding may occur if the lid is removed during the brewing cycles. 17. Keep the Opening Lever and the lid in place when the appliance is on. Improper use of this appliance may result in injury or damage to the product. EN 4 MyMilky PRO
EN IMPORTANT SAFEGUARDS When using electrical aplliance, basic safety precautions should always be followed to reduce the risk of fire, electric shock and/or injury to persons, including the following: 18. Close supervision is necessary when any appliance is used by or near children, or incapacitated individuals. 19. This appliance is not intended to be operated by means of an external timer or separate remote-control system. 20. To reduce the risk of injury, do not drape cord over the counter top or table top where it can be pulled on by children or tripped over unintentionally. THIS UNIT IS FOR HOUSEHOLD ONLY. MyMilky PRO 5
IMPORTANT SAFEGUARDS When using electrical aplliance, basic safety precautions should always be followed to reduce the risk of fire, electric shock and/or injury to persons, including the following: EN 21. A short power-supply cord is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord. 22. Longer extension cords are available and may be used if care is exercised in their use. 23. If a long extension cord is used: The marked electrical rating of the detachable power-supply cord or extension cord should be at least as great as the electrical rating of the appliance; The extension cord should be a grounding-type 3-wire cord; The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over. SAVE THESE INSTRUCTIONS Technical Data: Model»MyMilky Pro«, Type IDM15 (black) 120 Vac, 60Hz, 500W, Made in China. The MARTELLO reserves the right to make changes without prior notification to the external appearance of the product and / or technical conditions to improve the product. The MARTELLO Superespresso AG trademark. Copyright @2014. All rights reserved 6 MyMilky PRO
EN PRODUCT DESCRIPTION A Removable milk container with cool-touch case B Heat-resistant case C Lever D Button for warm frothing / Indicator light F Base E Button for cold frothing / Indicator light G Plastic transparent lid H Rubber seal I Whisk for frothing MyMilky PRO 7
FIRST USE The instructions on this page are valid for the first set-up of the device and for easy cleaning of the milk frother. EN WARNING: Never put the base (F) into dishwasher. Only the milk container (A), lid (G) and whisk (I) are dishwasher safe. Carefully read the instructions. Never use sharp cleaning agents, hard nylon brush or metal brush to avoid scratches on the stainless steel surface! Never clean with metal objects and never use abrasives. Never immerse into water or other liquids. 1 2 3 4 Unpack the box with care, keep all the packaging materials until you are satisfied everything is present and in working order. To disassemble unit for cleaning, open levers (C) from the base (F) by pulling out and upward to release the milk container (A). Clean the milk container (A) immediately after each use. Flush and clean the inner walls using warm soapy water and a non-abrasive cloth. Then dry with a soft towel. Remove the lid (G) from the milk container (A) and clean with warm soapy water. 8 MyMilky PRO
EN FIRST USE 5 NOTE! Never use sharp cleaning objects such as hard nylon or metal brushes or abrasive cleaning agents to avoid scratching on the stainless steel surface or on the inside of milk container. Clean the base (F) with a soft cloth. NOTE! Never put the base (F) in the dishwasher or immerse into water or other liquids. MyMilky PRO 9
DAILY USE - HEATING MILK EN 1 2 3 4 Plug in the unit. Pour the milk or chocolate milk into the milk container (A). Pay attention to the MAX capacity lines. Caution with overfilling to avoid frother from overflowing. Put the milk container (A) onto the base (F). 5 6 7 8 ERROR Ensure the rubber seal is in place on the lid (G) and remove the whisk (I) before placing back onto the milk container (A). Close both levers (C) by pressing down and pushing in. Push the button (D) for heating milk. The indicator light (D) will come on to indicate the heater is on. After heating is completed, the indicator light (D) will keep flashing for an additional 30 seconds. Error status: If the indicator light (D) keeps flashing, this means the machine is overloaded with milk. Pull out the power cable and pour some of the milk out until you get below the MAX line, plug the unit back in and try again. Unplug the connection plug. 10 MyMilky PRO
EN DAILY USE - HEATING MILK 9 10 Open the levers (C) and carefully pull the levers (C) out from the milk container (A) and remove lid (G). Pour your heated milk from the milk container (A) into your coffee or milk drink. MyMilky PRO 11
DAILY USE - FROTHING COLD MILK EN 1 2 3 4 Plug in the unit. Pour the milk into the milk container (A). Pay attention to the MAX capacity lines. Caution with overfilling to avoid frother from overflowing. Put the milk container (A) onto the base (F). 5 6 7 8 ERROR Ensure the rubber seal is in place and the whisk (I) is inserted before placing lid (G) onto the milk container (A). Close both levers (C) by pressing down and pushing in. 12 MyMilky PRO Pour the cold milk into the milk container (A) and push the button for cold frothing (E) then the indicator light (E) will turn on. After approx. 65 seconds the cold frothing is complete. After cold frothing is complete, the indicator light (E) will keep flashing for an additional 30 seconds. Error status: If the indicator light (E) keeps flashing. The machine is overloaded with milk. Pull out the power cable and pour some of the milk out until you get below the MAX line, plug the unit back in and try again. Unplug the connection plug.
EN DAILY USE - FROTHING COLD MILK 9 10 Open the levers (C) and carefully pull the levers (C) out from the milk container (A) and remove lid (G). Pour your frothed milk from the milk container (A) into your coffee or milk drink. MyMilky PRO 13
DAILY USE FROTHING & HEATING EN 1 2 3 4 Plug in the unit. Pour the milk into the milk container (A). Pay attention to the MAX capacity lines. Caution with overfilling to avoid frother from overflowing. Put the milk container (A) onto the base (F). 5 6 7 8 ERROR Ensure the rubber seal is in place and the whisk (I) is inserted before placing lid (G) onto the milk container (A). Close both levers (C) by pressing down and pushing in. Push the button (D) for heating & frothing. The indicator light (D) will come on to indicate the heater is on. After frothing is completed, the indicator light (D) will keep flashing for an additional 30 seconds. Error status: If the indicator light (D) keeps flashing, this means the machine is overloaded with milk. Pull out the power cable and pour some of the milk out until you get below the MAX line, plug the unit back in and try again. Unplug the connection plug. 14 MyMilky PRO
EN DAILY USE FROTHING & HEATING 9 10 Open the levers (C) and carefully pull the levers (C) out from the milk container (A) and remove lid (G). Pour your frothed milk from the milk container (A) into your coffee or milk drink. MyMilky PRO 15
CLEANING WARNING: The unit must be thoroughly cleaned after each use. To clean, do not use any harsh chemicals, corrosive or abrasive cleaning agents. EN IMPORTANT: Carefully read the instructions. Never use any harsh chemicals, corrosive or abrasive cleaning agents to clean your milk frother. 1 2 3 4 Unplug the unit. To disassemble unit for cleaning, open levers (C) from the bottom by pulling out and upward to release the milk container (A). Remove the lid (G) from the base (F), take the whisk out and let cool. The whisk can be removed from the lid by pulling out. Clean the milk frother immediatley after each use. The Lid (G), Milk container (A) and whisk (I) are dishwasher safe (upper rack). Place it carefully into your dishwasher and store in a safe place. 16 MyMilky PRO
EN CLEANING 5 6 NOTE! Never use sharp cleaning objects such as hard nylon or metal brushes or abrasive cleaning agents to avoid scratching on the stainless steel surface or on the inside of milk container. Never put the base (F) in the dishwasher or immerse into water or other liquids. Clean the base (F) with a soft cloth. MyMilky PRO 17
WARRANTY 1 Year Limited Warranty Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions (collectively JCS ) warrants that for a period of one year from the date of purchase, this product will be free from defects in material and workmanship. JCS, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. Do NOT attempt to repair or adjust any electrical or mechanical functions on this product. Doing so will void this warranty. This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. JCS dealers, service centers, or retail stores selling JCS products do not have the right to alter, modify or any way change the terms and conditions of this warranty. This warranty does not cover normal wear of parts or damage resulting for any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than JCS or an authorized JCS service center. Further, the warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes. What are the limits on JCS s Liability? JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or statutory warranty or condition. Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise. JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential or similar damages or loss of profits, or for any breach of contract, fundamental or otherwise, or for any claim brought against purchaser by any other party. Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from province to province, state to state or jurisdiction to jurisdiction. 18 MyMilky PRO EN
EN WARRANTY How To Obtain Warranty Service In the U.S.A.: If you have any question regarding this warranty or would like to obtain warranty service, please call 1.800.334.0759 and a convenient service center address will be provided to you. In Canada: If you have any question regarding this warranty or would like to obtain warranty service, please call 1.800.667.8623 and a convenient service center address will be provided to you. IMPORTED BY: Sunbeam Corporation (Canada). Limited doing business as Jarden Consumer Solutions, 20 B Hereford Street, Brampton, Ontario L6Y 0M1. Sunbeam Products, Inc. is a subsidiary of Jarden Corporation (NYSE:JAH). PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE. Printed in China IB Part # 177030 MyMilky PRO 19
RECIPES with MARTELLO CAFÈ RECIPES with MARTELLO CAFÈ RECIPES LATTE MACCHIATO 40 ml MARTELLO - Ristretto 210 ml milk First heat/froth the milk with your milk frother MARTELLO My Milky Pro. Fill the glass with the milk and foam and let it rest for about 60 seconds. Now put the glass under the coffee outlet of your MARTELLO espresso machine and let the coffee pour into the glass, so that the coffee builds a layer between milk and milk foam. VANILLA CAPPUCCINO 1 tbsp of vanilla sugar 50 ml milk 40 ml MARTELLO - Crema Gusto Some cocoa powder Heat/froth the milk with your milk frother MARTELLO My milky Pro. Then add vanilla sugar to the milk and stir it. Prepare your Espresso from your MARTELLO espresso machine as shown in the instruction manual. Now pour the milk and foam into the coffee mug, on top of the Espresso. Finally put some cocoa powder on top. 20 MyMilky PRO
with MARTELLO CAFÈ RECIPES with MARTELLO CAFÉ RECIPES with MAR For the caramel: 100 g sugar 40 g butter 150 ml whipping cream For the coffee: 40 ml MARTELLO - Gourmet Gold 150 ml milk (3,5 % fat) 2 tbsp. (tablespoon) Caramel sauce CARAMEL LATTE MACCHIATO Melt sugar in a small pot until it turns brown, take it off the stove and add butter and whipping cream, stir it and cook shortly. Heat up and froth the milk with your frother MARTELLO My Milky Pro. Put approximately 2 tbsp. of caramel sauce into a glass, add the milk and leave for 60 sec. Now add the coffee from the MARTELLO espresso machine to the glass so that the coffee builds a layer between the milk and milk foam. Finally put some caramel sauce on top of the milk foam. MyMilky PRO 21
www.martellocafe.ca