... A Vital Part of Connection World Cable Connectors Receptacles With Solder End Protective Caps N CONNECTORS COPYRIGHT ELECTRONICS 00
Type N 50 Ohm Coaxial Connectors DESCRIPTION The development of the Type N connector by the United States Army/Navy ran directly parallel to theescalation of U.S. involvement in WWII. It was finally released in 94, shortly after the U.S. officially ment field and join the coaxial cable of the radio frequency extensively entered the war, and since that time it has been a staple in RF and Microwave applications all over the world. Due to N type connectors joins by one whorl, it has the characteristic of raliable and strong ant-vibration nature, machinery and electric performance finely. It is used in vibration and environment abominable radio equipment of terms and instrument and ground launch system join the coaxial cable of the radion frequency extensively. CONTENTS Description... Interface dimensions... Technical data... 3 Cable connectors... 4 Receptacles with solder end... PCB connectors... 4 Protective cap... 5 Assembly instruction... 6 Mounting hole... Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
Type N INTERFACE PLUG JACK LETTER mm inch mm inch LETTER min. max. min. max. min. max. min. max. A 0.3.03.005.3 A 9.05 9.9.356.36 B.80 3.56.0.40 B 4.75 5.5.87.07 C 5.33 5.83.0.9 C.0.95.047.077 D.06.066 D 4.4 5..73.0 E 4.54 5.39.79. E 6.8 9.68.354 F 4.05 4.0.59.65 F 0.9..49.44 G 0.3 0.43.403.4 G DIA 6.98 7.0.75.76 H DIA 8.7 8.37.36.39 H DIA 8.03 8.3.36.30 J DIA 6. 6..634.638 J DIA 8.53 8.73.336.344 K DIA 0.9.83.87 K DIA 5.65 5.85.66.64 L DIA 3.0 3.05.8.0 L DIA 3.0 3.05.8.0 M DIA.63.67.064.066 Interface dimensions conformable to the standards: International: IEC669-6 Europe: CECC 0 USA: MIL-STD-348A/304, IP rating (interface, mated) IP68 Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
TECHNICAL DATA ELECTRICAL DATA Impedance Frequency range Dielectric withsanding voltage V.S.W.R. Insulation resistance Contact resistance RF leakage 50 Ohm DC 0 GHz,500 volts rms straight connectors:.3 max 0- GHz; right angle connectors:.35 max 0- GHz 5*000 MΩ Contact.0 mω Outer Contact.0 mω -90 db minimum at 3 GHz MECHANICAL DATA Braid/Jacket Cable Affixment Conductor Cale Affixment Mating Assembly Torque (body/clamp nut) Crimps: hex braid crimp;clamps:screw-thread nut and braid clamp Crimp: crimp or solder;all others: solder only 5/8-4 threaded coupling 8/ lb-ft (5/30 N-m) MATERIAL DATA Male Contact Female contact Gasket Crimp Ferrule Brass, silver or gold plated Phosphorous bronze or beryllium copper, silver or gold plated Other Metal Parts Brass Silicone rubber Copper ENVIRONMENTAL Temperature Range Thermal shock Moisture resistance Corrosion Vibration TFE: -65 C to +65 C MIL-STD-0, method 07, test condition A- MIL-STD-0, method 06 MIL-STD-0, method 0, test condition B MIL-STD-0, Method 04, Condition D Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China 3
CABLE CONNECTORS Straight cable plugs (male) RoHS 50-03-M06-00 Semi-rigid.4/RG40 A0 Cable entry soldered 4.00 [.945] 4.00 [.57] 3.70 [.46 DIA.] 50-03-M-00 Semi-rigid.086/RG405 A0 Cable entry soldered 3.50 [.95] 3.50 [.38].0 [.087 DIA.] 50-03-M3-003 Semi-rigid.50 A0 Cable entry soldered 3.60 [.99] 6.50 [.56 DIA.] SW 9 [.750 HEX.] Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China 4
CABLE CONNECTORS Straight cable plugs (male) RoHS 50-03-M04-004 LMR00/RG74/RG36 A0 5.00 [.984].70 [.067 DIA.] 0.00 [.394] 3.0 [.6 DIA.] 4.00 [.57] 50-03-M8-005 LMR95/RG58 A03 30.30 [.93] 3.0 [.6 DIA].70 [.500] 5.40 [.3 DIA.] 6.5 [.46 DIA] 50-03-M0-006 LMR400 A03 3.50 [.80] 7.5 [.95 DIA.] 5.00 [.59] 0.90 [.49 DIA.].0 [.480 DIA.] Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China 5
CABLE CONNECTORS Straight cable plugs (male) RoHS 50-03-M0-007 LMR40 A03 30.00 [.8] 4. [.65 DIA.] 3.00 [.5] 6.80 [.68 DIA.] 8.00 [.35 DIA.] 50-03-M9-008 LMR600 A03 46.50 [.83].00 [.47 DIA.] 9.00 [.748] 5.50 [.60 DIA.] 7.00 [.669 DAI.] 50-03-M0-009 LMR300 A03 3.00 [.0] 5.00 [.97 DIA.] 4.00 [.55] 8.0 [.33 DIA.] 9.40 [.370 DIA.] 6 Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
CABLE CONNECTORS Straight cable plugs (male) RoHS 50-03-4M04-00 LMR00/RG74/RG36 A04 3.50 [.80] Cable entry clamp SW.00 [.433 AF.] SW.00 [.433 HEX.] 50-03-4M8-0 LMR95/RG58 A04 3.50 [.80] Cable entry clamp SW.00 [.433 AF.] SW.00 [.433 HEX.] 50-03-4M0-0 LMR400 A04 Cable entry clamp 38.00 [.496] SW 6.00 [.630 AF.] SW 6.00 [.630 HEX.] Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China 7
CABLE CONNECTORS Straight cable plugs (male) RoHS 50-03-4M9-03 LMR600 A04 45.50 [.79] Cable entry clamp.00 [.866 DIA.] SW 0.00 [.787 AF.] SW 0.00 [.787 AF.] 50-03-4M5-040 7/8'' Cable A05 80.80 [3.8] Cable entry clamp 40.00 [.575 DIA.] SW 9.00 [.748 HEX.] SW 36.00 [.47 AF.] SW 36.00 [.47 AF.] 50-03-4M6-039 /'' Cable A06 6.80 [.47] Cable entry clamp.30 [.878 DIA.] SW 9.00 [.748 AF.] SW 0.00 [.787 AF.] 8 Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
CABLE CONNECTORS Right angle cable plugs (male) RoHS 50-3-M06-06 RG40/Semi-rigid.4 A07 9.00 [.4] Cable entry soldered 9.50 [.374] 3.70 [.46 DIA.] 4.5 [.955] 9.50 [.374] 50-3-M04-07 LMR00/RG74/RG36 A08 8.80 [.34].65 [.065 DIA.] 9.50 [.768] 0.00 [.394] 3.0 [.6 DIA.] 4.00 [.57 DIA.] 50-3-M0-08 LMR40 A08 3.50 [.40] 4. [.65 DIA.] 5.00 [.59 DIA.] 5.00 [.984] 3.00 [.5] 6.80 [.68 DIA.] 8.00 [.35 DIA.] Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China 9
CABLE CONNECTORS Right angle cable plugs (male) RoHS 50-3-M0-09 LMR400 A08 3.00 [.60] 7.5 [.95 DIA.] 8.50 [.] 5.00 [.59] 0.90 [.49 DIA.].0 [.480 DIA.] 50-3-4M0-00 LMR400 A04 7.50 [.689] 58.0 [.9] Cable entry clamp 39.40 [.55] SW 6.00 [.630 AF.] SW 6.00 [.630 HEX.] 8.00 [.709 DIA.] 50-3-4M6-04 /'' Cable A06 65.75 [.589] Cable entry clamp 35.40 [.394] 7.50 [.689] SW 9.00 [.748 HEX.] SW 9.00 [.748 HEX.].30 [.878 DIA.] Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China 0
CABLE CONNECTORS Straight cable jacks (female) RoHS 50-0-M8-0 RG58/LMR95 A03 5/8-4UNEF-A 7.80 [.094] 3.0 [.6 DIA].70 [.500] 5.40 [.3 DIA.] 6.5 [.46 DIA] 50-0-M0-03 LMR400 A03 33.30 [.3] 7.5 [.95 DIA.] 5.00 [.59] 5/8-4UNEF-A 0.90 [.49 DIA.].0 [.480 DIA.] 50-0-M0-04 LMR40 A03 5/8-4UNEF-A 9.80 [.73] 4. [.65 DIA.] 3.00 [.5] 6.80 [.68 DIA.] 8.00 [.35 DIA.] Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
CABLE CONNECTORS Straight cable jacks (female) RoHS 50-0-4M0-05 LMR400 A04 Cable entry clamp 4.40 [.630] 8.00 [.709 DIA.] 5/8-4UNEF-A SW 6.00 [.630 AF.] SW 6.00 [.630 AF.] 50-0-4M8-06 LMR95/RG58 A04 35.50 [.398] Cable entry clamp 5/8-4UNEF-A 5.90 [.66 DIA.] SW.00 [.433 AF.] SW.00 [.433 HEX.] 50-0-4M6-07 /'' Cable A06 56.80 [.36] Cable entry clamp SW 9.00 [.748 HEX.] SW 9.00 [.748 HEX.] 5/8-4UNEF-A.30 [.878 DIA.] Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
CABLE CONNECTORS Straight bulkhead cable jacks (female) RoHS Mount Hole 50-0-D8-08 RG58/LMR95 A03 M0 35.0 [.386].00 [.866] MAX. 7.00 [MAX..76].00 [.866] 5/8-4UNEF-A 3.0 [.6 DIA.].70 [.500] 5.40 [.3 DIA.] 6.5 [.46 DIA] SW 3.50 [.53 AF] Mount Hole 50-0-D04-09 LMR00/RG74/RG36 A0 M0 3.0 [.8] 9.50 [.768] MAX. 4.50 [MAX..77].00 [.866] 5/8-4UNEF-A.70 [.067 DIA.] 0.00 [.394] 3.0 [.6 DIA.] 4.00 [.57] SW 3.50 [.53 AF] Mount Hole 50-0-D06-030 LMR40 A09 M0 Cable entry soldered 33.0 [.307].00 [.866] MAX. 7.00 [MAX..76].00 [.866] 5/8-4UNEF-A 3.70 [.46 DIA.] SW 3.50 [.53 AF] SW 3.50 [.53 AF] Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China 3
CABLE CONNECTORS Straight panel cable jacks(female) RoHS Mount Hole 50-0-8F8-03 LMR95/RG58 A03 M0 5/8-4UNEF-A 8.70 [.736].00 [.079] 7.0 [.07] 3.0 [.6 DIA.] 5.40 [.000 SQ.] 8.5 [.79] 4-3.5 [.8 DIA.] 8.5 [.79].70 [.500] 5.40 [.3 DIA.] 6.5 [.46 DIA] Mount Hole 50-0-8F0-03 LMR400 A03 M0 5/8-4UNEF-A 33.00 [.99] 8.70 [.736] 5.40 [.000 SQ.].00 [.079] 8.5 [.79] 7.5 [.95 DIA.] 4-3.5 [.8 DIA.] 8.5 [.79] 5.00 [.59] 0.90 [.49 DIA.].0 [.480 DIA.] Mount Hole 50-0-8F0-033 LMR400 A04 M0 Cable entry clamp 5.40 [.000 SQ.] 8.5 [.79] 4-6.00 [.36 DIA.] 4-3.5 [.8 DIA.] 8.70 [.736].00 [.079] 39.0 [.540] 8.5 [.79] 5/8-4UNEF-A SW 6.00 [.630 AF.] SW 6.00 [.630 HEX.] 4 Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
RECEPTACLES WITH SOLDER END Receptacles, jacks (female) RoHS Mount Hole 50-0-8F7-034 M03 Panel mounted 5/8-4UNEF-A 33.70 [.37] 5.00 [.59] 9.00 [.354].60 [.063].7 [.050 DIA.] 4.0 [.6 DIA.] 7.50 [.689 SQ.].70 [.500].70 [.500] 4-3.0 [. DIA.] Mount Hole 50-0-8F7-035 M03 Panel mounted 5/8-4UNEF-A 9.80 [.73].7 [.050 DIA.] 4.0 [.6 DIA.] 7.50 [.689 SQ.].70 [.500].70 [.500] 4-3.0 [. DIA.].00 [.079].50 [.059] 9.50 [.374] Mount Hole 50-0-8F-036 M0 Panel mounted 5/8-4UNEF-A 7.30 [.075] 5.40 [.000 SQ.] 6.80 [.66] 8.5 [.79].40 [.094 DIA.] 3.00 [.8 DIA.] 4-3.5 [.8 DIA.] 8.5 [.79] 6.50 [.56].00 [.079] Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China 5
RECEPTACLES WITH SOLDER END Receptacles, jacks (female) RoHS Mount Hole 50-0-8F-037 M03 Panel mounted 5/8-4 UNEF-A.00 [.866] 3.00 [.8] 7.00 [.669] 0.46 [.08] 3.00 [.8 DIA.] 7.50 [.689 SQ.].70 [.500] 4-3.0 [. DIA.].70 [.500] Mount Hole 50-0-8A-038 M04 Panel mounted 6.60 [.653] MAX..5 [MAX..098] 9.60 [.65].40 [.094 DIA.] 3.00 [.8 DIA.] 5/8-4UNEF-A 5/8-4UNEF-A 6.00 [.36] SW 9 [.748 HEX.].70 [.067 DIA.] 7.0 [.07] 6 Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
PROTECTIVE CAPS RoHS 50-03-9N-04 Protective cap for jacks (females) 9.70 [.776] 4 [.57 DIA.] 80 [3.50] 50-0-9N-043 Protective cap for plugs (males) 0.50 [.807] 0.00 [.787] 4 [.57 DIA.] 80 [3.50] 5/8-4UNEF-A Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China 7
ASSEMBLY INSTRUCTIONS A0 Contact Stripping Dimensions a Heatshrink sleeve (option) Stripping Length (mm [in]) a 50-03-M06-00 Semi-rigid.4/RG40 5.0 [.97] 50-03-M-00 Semi-rigid.086/RG405 3.5 [.38] 50-03-M3-003 Semi-rigid.50 5.5 [.7]. Slide the heatshrink sleeve onto the cable (option). Strip the cable as Striping Dimensions. 4. Solder the body onto the cable.. Slide the center contact on until it bottom against the cable dielectric. Solder the center contact onto the cable. 5. Slide the heatshrink sleeve over the body and heatshrink it in place (option). 3. Slide the cable into the body until it stops. 8 Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
ASSEMBLY INSTRUCTIONS A0 Ferrule Guide Pin Stripping Dimensions c b a Heatshrink sleeve (option) 50-03-M04-004 50-0-D04-09 LMR00/RG74/RG36 HEX. Crimp Tool (mm [in]) Stripping Length (mm [in]) 3.5 [.8] 3 [.8] 3.5 [.38] a b c 3 [.5]. Slide the heatshrink sleeve onto the cable (option). Slide the ferrule onto the cable. Strip the cable as Striping Dimensions. 4. Slide the cable into the body until stops.. Slide the guide pin on until it bottom against the cable dielectric. Solder the guide pin onto the cable. 3 5. Slide the ferrule over the braid. Crimp the ferrule with crimping tool (see table). 3. Fan the braid. 6. Cut the excess of braid if necessary. Slide the sleeve over the ferrule and heatshrink it in place (option). Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China 9
ASSEMBLY INSTRUCTIONS A03 Ferrule Contact Stripping Dimensions c b a Heatshrink sleeve (option) 50-03-M8-005 50-0-M8-0 50-0-D8-08 50-0-8F8-03 50-03-M0-007 50-0-M0-04 50-03-M9-008 HEX. Crimp Tool (mm [in]) LMR95/RG58 5.4 [.3] LMR40 6.8 [.68] a Stripping Length (mm [in]) b [.079] 3 [.8] 3.5 [.53].5 [.098] 50-03-M0-009 LMR300 8. [.33] 5 [.8] 8 [.709] 3 [.8] 50-0-M0-03 5.5 [.7] 50-03-M0-006 LMR400 0.9 [.49] 9 [.748] 4 [.57] 50-0-8F0-03 5 [.8] LMR600 5.8 [.65] 6 [.36] 3 [.8] 3 [.906] c. Slide the heatshrink sleeve onto the cable (option). Slide the ferrule onto the cable. Strip the cable as Striping Dimensions. 4. Slide the cable into the body until stops. 3. Slide the center contact on until it bottom against the cable dielectric. Solder the center contact onto the cable. 5. Slide the ferrule over the braid. Crimp the ferrule with crimping tool (see table). 3. Fan the braid. 6. Cut the excess of braid if necessary. Slide the sleeve over the ferrule and heatshrink it in place (option). 0 Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
ASSEMBLY INSTRUCTIONS A04 Washer Contact Stripping Dimensions c b Nut Rubber Insert Sleeve a a Stripping Length (mm [in]) b c Recommended Coupling Torque 50-03-4M04-00 50-03-4M8-0 50-0-4M8-06 LMR00/RG74/RG36 LMR95/RG58 3 [.8] 6 [.36] 6 [.36] 50-03-4M0-0 50-3-4M0-00 50-0-4M0-05 LMR400 5 [.97] [.433] [.433] 450N cm 50-0-8F0-033 50-03-4M9-03 LMR600 6 [.36] 3 [.5] 3 [.5]. Slide the nut, the washer, the rubber and another washer onto the cable. Strip the cable as Striping Dimensions. 4. Slide the nut over the cable assembly.. Fold the braid back. Insert the insert sleeve into the cable (under the braid) until the back surface flush with the cable dielectric. 5. Screw sub-assembly into the body with wrench, recommended coupling torque see table. 3. Slide the center contact on until it bottom against the cable dielectric. Solder the center contact. Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
ASSEMBLY INSTRUCTIONS A05 Back Nut O-Ring Stripping Length (mm [in]) Recommended Coupling Torque 50-03-4M5-040 7/8'' Cable See Figure 800N cm. Stripping dimensions as shown, Several problems should be paid attention in stripping: (a) The end of the outer conductor s stripping should be on the wave peak. (b) The end surface of the dielectric should be chamfered to mmx45 (c) Removing the burr at the inner conductor s inside lip (d) The end of the jacket surface should be chamfered to 0.5mmx45. (e) Removing impurities such as copper scale and burr at the end of the cable surface. 3. Screw off the back nut, assemble the back nut to the cable and make sure that the clamp is in the trough of the cable as shown by the following figure, flare the outer conductor of the cable so as to make sure that the outer conductor touch slanting surface of the inside hole at the clamp as shown. Expand Section Clamp 0.5mmx45 mm Outer Conductor Peak mmx45 4. Combine the main body and back nut by screwing as shown. Keep the back nut and the cable motionless, then tighten the main body and back nuts with a wrench.. Put the O-ring in the trough of the cable as shown. O-Ring Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
ASSEMBLY INSTRUCTIONS A06 Back Nut Striping Dimensions (c) b a O-Ring a Stripping Length (mm [in]) b c Recommended Coupling Torque 50-0-4M6-07 50-03-4M6-039 /'' Cable 0 [.394] 8 [.709] 8 [.0] 800N cm 50-3-4M6-04. Stripping dimensions as table, Several problems should be paid attention in stripping: (a) The end of the outer conductor s stripping should be on the wave peak. (d) Inner conductor should be chamfered to mmx45. (e) Removing impurities such as copper scale and burr at the end of the cable surface. Peak 3. Screw off the back nut, assemble the back nut to the cable and make sure that the clamp is in the trough of the cable as shown by the following figure, flare the outer conductor of the cable so as to make sure that the outer conductor touch slanting surface of the inside hole at the clamp as shown. Expand Section Clamp mmx45 Outer Conductor 4. Combine the main body and back nut by screwing as shown. Keep the back nut and the cable motionless, then tighten the main body and back nuts with a wrench.. Put the O-ring in the trough of the cable as shown. O-Ring Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China 3
ASSEMBLY INSTRUCTIONS A07 Back Nut Stripping Dimensions a Heatshrink sleeve (option) Stripping Length (mm [in]) 50-3-M06-06 RG40/Semi-rigid.4 5.5 [.7]. Slide the heatshrink sleeve onto the cable (option). Strip the cable as Striping Dimensions. 3. Screw the back nut onto the body.. Slide the cable into the body until it stops. Solder the inner conductor. 4. Slide the sleeve over the body and heatshrink it in place (option). 4 Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
ASSEMBLY INSTRUCTIONS A08 Ferrule Cap Stripping Dimensions c b a Heatshrink sleeve (option) HEX. Crimp Tool (mm [in]) a Stripping Length (mm [in]) b c 50-3-M04-07 50-3-M0-08 LMR00/RG74/RG36 LMR40 3.5 [.8] 6.8 [.68] 3 [.8] 5 [.97] 3 [.8] 6 [.630] 0 [.787] 50-3-M0-09 LMR400 0.9 [.49] 4 [.57] 5 [.97] 3 [.906]. Slide the heatshrink sleeve onto the cable (option). Slide the ferrule onto the cable. Strip the cable as Striping Dimensions. 4. Crimp the ferrule with crimping tool (see table). Solder the inner conductor. 3. Fan the braid. 5. Place the cap into the body. 3. Push the body under the braid. Slide the ferrule over the braid. 6. Press on the cap until stops. Slide the sleeve over the ferrule and heatshrink it in place (option). Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China 5
ASSEMBLY INSTRUCTIONS A09 Stripping Dimensions a Heatshrink sleeve (option) Stripping Length (mm [in]) 50-0-D06-030 RG40/Semi-rigid.4 4.5 [.77]. Slide the heatshrink sleeve onto the cable (option). Strip the cable as Striping Dimensions. 4. Slide the heatshrink sleeve over the body and heatshrink it in place (option).. Slide the cable into the body until it stops. 3. Solder the body onto the cable. 6 Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China
MOUNTING HOLES 6.0 [.638 DIA.] 8.5 [.79] 3.50 [.38 DIA.].70 [0.500] 4-3.30 [.30 DIA.] 6.0 [.634 DIA.] 8.5 [.79] 4.0 [.65 DIA.].70 [0.500] 3.90 [.547] M0 M0 M03 6.0 [.634 DIA.] 4.60 [.575] M04 Tel : +86-5-8443 63 Fax : +86-5-8698 88 Email : sales@cmpter.com Website: www.cmpter.com #45 ZhongShan East Road, ZhenJiang 003, JiangSu, China 7
Cmpter Electronics, Ltd. Office Adress: #45 ZhongShan East Road, ZhenJiang, JiangSu China. Tel:+86 5 8443 63 Fax:+86 5 850 5485 Email: sales@cmpter.com Website: http://www.cmpter.com