OPERA 12, 17 & 46 Radant panel heater horzontal, vertcal and low Installaton & Operatng Instructons 421AA2814.B00 09-2016 ATTENTION : Documents to be kept by the end-user. Please read before any operaton.
Dear owner, Congratulatons on the purchase of ths premum electrc heater. CONVECTAIR develops and produces the hghest qualty heatng product n the electrcal ndustry. To obtan the best results and the ultmate n performance and comfort, please take a moment to read the nstallaton, operaton and mantenance nstructons detaled n ths manual. WARNING :. IT MUST NOT BE CONNECTED TO A WALL THERMOSTAT. 1- RECOMMENDED SET-UP...PAGE 3 2- INSTALLATION AND MOUNTING...PAGE 6 3- ELECTRICAL CONNECTION...PAGE 8 4- QUICKSTART GUIDE...PAGE 9 5- OPERATING INSTRUCTIONS...PAGE 10 6- OVERHEAT CONTROL...PAGE 24 7- MAINTENANCE...PAGE 25 8- TROUBLESHOOTING...PAGE 26 9- IDENTIFICATION OF YOUR HEATER...PAGE 27 10- WARRANTY INFORMATION...PAGE 28 2
! Safety 3
4
Any Tout obstacle ex: : curtans volages B 0.2 m 15 cm (6 n) 0.2 m C 20 cm (8 n) E 2.5 0,15 cm m (1 n) 0.2 m B 15 cm (6 n) A 75 cm 1 (30 m n) Floor Sol CAUTION: PLEASE MAINTAIN THE MINIMUM REQUIRED CLEARANCES (Fg. A). CONVECTAIR RECOMMENDS AN INSTALLATION HEIGHT OF 15 CM (6 IN). Mnmum clearances In front (A) Sdes (B) Above (C) Underneath (E) Recommended heght 7732-CXX-FS 75 cm (30 n) 15 cm (6 n) 20 cm (8 n) 2.5 cm (1 n) 15 cm (6 n) 7733-CXX-FS 75 cm (30 n) 15 cm (6 n) 20 cm (8 n) 2.5 cm (1 n) 15 cm (6 n) 7734-CXX-FS 75 cm (30 n) 15 cm (6 n) 20 cm (8 n) 2.5 cm (1 n) 15 cm (6 n)!
Hauteur et CONVECTAIR), follow these drectons: 1- Free mountng brackets by pressng and pullng both lockng tabs on the back of the heater (Fg. B). 2- Place the center of the mountng bracket's bottom holes (no. 2 Fg. B2) at the measure C (see tables Fg. C - D - E - F) from the ground and make a mark. 3- Check horzontalty of the mountng bracket, then mark the two top holes and perce the 4 holes for fastenng. 4- Replace mountng bracket and fasten t approprately wth screws (not ncluded). Encombrement de l apparel Outlne of unt 258 A Example of mountng bracket: 7733 500 W 2 500=>1250W A Juncton box 25 cm (10 n) 15 cm (6 n) 150 C Measure C 2 B 28 104 t Largeur oun Sol Fgure B2 Hauteur et Encombrement de l apparel Outlne of unt Largeur t Hole spacng Entaxe D A Juncton box 25 cm (10 n) Sol 150 15 cm (6 n) oun B C Capacty (W) Measures Heater wdth Heater heght C Cap. (W) Measures Hole spacng Heater wdth Heater heght A B C
Cap. (W) Measures Hole spacng Heater wdth Heater heght A B C D Encombrement de l apparel Hauteur Outlne of unt Hole spacng Entaxe D A B et Juncton box Largeur t 45 cm (18 n) Sol 150 oun 15 cm (6 n) C Encombrement de l apparel Outlne of unt Hole spacng D Entraxe Cap. (W) Measures Hole spacng Heater wdth Hauteur heght A B C A Hauteur et Juncton box 20 cm (8 n) B 150 15 cm (6 n) C Largeur t Sol oun
! Please read carefully the whole nstallaton and operatng nstructons before connectng the heater! WARNING : To prevent short crcuts and electrcal shocks turn the power off at the man panel before attemptng the nstallaton or makng any repars. If you are usng a programmer system, make sure to cut the power off ALL electrcal heatng crcuts of the heaters wred to the plot wre. - O eoen tt ou ete e ntlle ule eletn n n one wt ntonl n lol codes. - s ete ust e connected to 240 olt 60 ccles ccut nd wt n ote ee. ut ll electcl cuent efoe connectn te ete to od socs nd des to te unt. - e st te ou onect ets lt soe could e elesed due to te unn of oducton esdues. s s nol nd sould dse fte 2 to 3 nutes. RESPECT WIRE COLOR WIRING CANADA * = Cables 3/12 or FAS 105 18/2 approved 300 volt. CANADA P * P (PW) = PURPLE R = RED B = BLACK G = GREEN C = COPPER P - ou ut onnet te oun e of te ete een e) wt te oe we. - onnet te owe le to te e n l le. - ee onnet te lot-we ule we to te eletl ul no oun t. - e ule we wt te el t te etet oul not e ue fo te eletl onneton. t ue onl f te ete onnete wt te O oe te o te wll ount ontolle. - te unt on te wll et efoe tunn te owe on.
- urnn O/SA te eater ress te e to turn te eater O or SA. - o set te teperature or. - e Te O selector ress on te e to coose te operatng mode. YOU WISH PRESS USE THE FONCTION To mantan te room at te desred comfort temperature. To mantan te room at te desred setbac temperature. To mantan te room at frost protecton temperature. COMFORT SETBACK FROST PROTECTION SCREEN DISPLAY An automatc setbac durng your absence. ABSENCE DETECTOR efore actvatng any programmng mode please refer to page 14 Settng te tme and date. ressng on te ey for 3 seconds toggles between te ATO and ST programmng modes. To apply te settngs sent by your central programmng system or power management system. To apply a preset or customsed program. 3 seconds «AUTO» PROGRAMMING «PRESET» PROGRAMMING AUTO 2 P2 -«Open Wndow detector» o enable or dsable ts functon ress te e for 3 seconds to enable or dsable ts functon. - Ideal Temperature «C déal» functon re press te e to reset te standard operatn mode factor settns 19 C for comfort and 155 C for CO.
ress bot eys to - rogram te eater - Set te tme «Open Wndow» functon Consumpton ndcator Heatng ndcator rogram - reset 1/2/3 - Custom 4/5/6 Temperature settng eys ocaton of te programmng cassette optonal. selecton ey Reset to deal temperature settng eatng O/STA ey Mae sure you remove te protectve lm from te control panel. 5.1 - Turnng O/STA te eater To turn te unt on press. Te screen wll dsplay te Comfort temperature. To place te eater on STA mode press. Te screen turns off. Te eater eeps te current settngs on le even durng a power outage for a mamum of 12 ours.
5.2 - Comfort / Settng the desred temperature: : ress te or eys to rase or lower te desred Comfort temperature n steps of 0.5 C 1 F. To ensure tat te temperature stablses at te desred temperature, te doors and wndows of te room sould be closed. 5.3 - The MODE selector : ress repeatedly on te ey. Te selector enables selectng up to 6 functons YOU WISH PRESS USE THE FUNCTION SCREEN DISPLAY To mantan te room at te desred comfort temperature. COMFORT To mantan te room at te desred setbac temperature. SETBACK To mantan te room at frost protecton temperature. FROST PROTECTION An automatc setbac durng your absence. ABSENCE DETECTOR To apply te settngs sent by your central programmng system or power management system. To apply a preset or customsed program. Before actvatng any programmng mode, please refer to page 14 secton Settng te tme and date. 3 seconds «AUTO» PROGRAMMING «PRESET» PROGRAMMING AUTO P2* 2 eemple 2 *ressng on te ey for 3 seconds toggles between te ATO and RST programmng modes.
5.4 - AUTO Programmng mode Ts mode enables automatc operaton of te eater over plot wre from a central programmng system e CONCTAIRS rogrammer system or power management system. AUTO ress successvely on te ey untl te ATO symbol s dsplayed. Note ressng on te for 3 seconds toggles between te ATO and RST programmng modes see p. 19. COMMANDS SENT OVER PILOT WIRE Heatng OFF Setback Frost Protecton SCREEN DISPLAY AUTO AUTO AUTO RESULT Heatng s mmedately turned off. Te temperature s lowered by 3.5 C compared to te Comfort settng, or as desred. Te temperature s mantaned at about 7 C.
Specc condtons In Comfort, conomy and Frost rotecton overrde mode, Frost rotecton and Heatng OFF commands sent by te central programmng e CONCTAIRS rogrammer system or energy management systems wll ave a prorty. Ts s ndcated by a blnng ATO symbol. Selected functons 19,0 C ECO HG Central Programmng System or Energy Management System Command over plot wre: Frost Protecton '' AUTO '' Command over plot wre : Heatng OFF '' AUTO '' 5.5 - Controls lock : Smultaneously press te and eys for tree seconds to loc or unloc te eypad. Ten, f you press any ey on te eypad,te screen wll dsplay «NON». Te eypad s loced and no operaton s possble. Ts functon dsables any operatons from te control panel n any operatng mode to prevent te settngs from beng canged, for eample, by cldren. 5.6 - Tme dsplay : RO ress brey on and eys to dsplay te current tme.
5.7 - Settng the tme and date : -In all cases, to use te preset programs, you rst must set te tme and date of your eater factory default 0000. -In case of a power outage eceedng 12 ours, you must reset te tme on your devce. A- Settng te tme 3 seconds Frmly press te and eys for 3 seconds to access te programmng menu. RO Te «r» symbol s dsplayed. ress te or to select te tme settng functon n te drop-down menu «Hr» and conrm by pressng te ey. + Pr Hr P4 Ext P6 P5 Cange te our settng usng te and eys and conrm by pressng te ey. Cange te mnute settng usng te and eys and conrm by pressng te ey. B - Settng te weeday Cange te weeday O = Monday, O MA = Tuesday, O M = Wednesday,etc. usng te and eys. + Conrm by pressng te ey. Pr Hr P4 P5 To ext, press on or eys untl te xt opton appears n te drop-down menu. ress to conrm and ext. P6
5.8 - Setback functons: 4.8.1- Setbac CO ress successvely te ey untl te Setbac CO s dsplayed. To vew te CO set pont, press brey te or eys. To cange te CO set pont temperature ress on te ey for 3 seconds untl te CO set pont temperature ases. ress te or eys untl obtanng te desred CO temperature. ress te ey to conrm. It s recommended to use ts mode for temporary absences between 2 and 24 ours, or overngt. Ts mode lowers room temperature by approxmately 3.5 C relatve to te Comfort temperature set pont. 5.8.2- Frost rotecton H ress successvely on te ey untl te Frost rotecton mode H s dsplayed. For maxmum energy savngs, n case of longer term absence 24 rs. or more, t s recommended to use ts settng, wc wll mantan te room temperature at about 7 C. 5.8.3 - Absence detector ress successvely on te ey to select te absence detecton mode. Te symbol wll be dsplayed. Te Absence etector mode allows to lower te eatng degree n te case of an absence and to aceve eatng savngs. Tere are tree absence detecton operatng optons see followng pages.
Opton 1 : (default mode) : ECO order from nternal programmng or plot wre s prortary even f a presence has been detected. Opton 2 : ECO order from programmng s not prortary. In case of a presence detecton, the heater goes on comfort mode. Opton 3 : The heater doesn t follow programmng orders. Auto Auto + + Turn off the heater, press smultaneously the and seconds untl detecton appears. - Select the desred detecton opton usng the + or keys. - Press the MODE key Note n all cases te orders for Frost rotecton and Heat OFF from te plot wre are prorty. Detecton Prorty to energy savngs Movement detecton mode and programmng Px P1 or P2...P6 or Command over Plot Wre or nterne programmng Result Comfort Gradual transton to ECO (n 1:30 hr) AUTO absence ECO ECO Comfort Immedate swtch to Comfort movement ECO ECO P1
movement Detecton ECO Prorty to comfort Movement detecton mode and programmng Px P1 or P2...P6 or Command over Plot Wre or nterne programmng Result absence Comfort Gradual transton to ECO (n 1:30 hr) AUTO ECO Comfort movement Detecton Prorty to energy savngs Movement detecton mode wthout programmng absence Command over Plot Wre or nterne programmng - Result Gradual transton to ECO (n 1:30 hr) movement - Comfort 5.8.4 - Open Wndow detector To enable or dsable ts functon, press te ey for 3 seconds. Te symbol wll be dsplayed on te screen. Te symbol wll bln f te unt as ceased eatng followng te detecton on an open wndow or door. To cancel te STANB order, press te restart te eater. ey to Ts functon automatcally suts off te eater wen a drop n room temperature s detected suc as an open wndow or door.
5.8.5 - Consumpton ndcator It s an ndcator of beavour tat allows vewng te energy consumpton status of your eater. Consumpton Indcateur de ndcator consommaton - reen ndcator lgt = economcal - Indcator lgt sftng toward red = less economcal. Ts ndcator allows to montor and adust te desred temperature dependng on ts mpact on consumpton. 5.8.6 - Heatng ndcator Te ndcator sows tat your eater s warmng up. Wen te desred temperature as stablsed, ts ndcator turns on and off accordng to eatng needs. 5.8.7 - Ideal temperature Automatc return to te recommended temperatures Brey press te ey to reset te standard operatng mode factory settngs - STBAC mode settng at 15.5 C 60 F - COMFORT mode settng at 19 C 66 F Optmsed settng : ress te ey for 10 seconds to congure te operatng mode and aceve maxmum savngs of energy - SETBACK mode settng at 15.5 C 60 F - COMFORT mode settng at 19 C 66 F - Actvaton of te Open Wndow functon - Actvaton of te ATO programmng mode. Long press Ts functon automatcally adusts te eater for an optmal comfort / economy rato.
5.8.8 - Operatng reset programs 1/2/3 or customsable programmes 4/5/6 3 seconds RO In ts mode, te eater operates n automatc daly mode accordng to te Comfort set pont or te Setbac set pont. Te date and tme must be set beforeand n order to be able to create te programs see p. 14. If you ws to assgn a daly program for eac day of te wee P1 P2 + P3 P5 P4 - ress smultaneously for 3 seconds te and eys. P1 P2 + P3 P5 P4 - Te screen dsplays «r».ress te ey. - Assgn one of te avalable programs predened or custom for eac day of te wee usng te and eys to scroll troug te dropdown menu. - ress te ey to conrm.te screen dsplays «r». - To ext, press te or eys untl te «Ext» opton s dsplayed n te drop-down menu. - ress te ey to conrm and ext. to ext P1 Pr + P2 P3 Hr Ext P4 P5 + P4 P6 P5
Preset programme Monday du Lund au to Vendred Frday 5h à 9h { 0h 2 4 6 8 10 12 14 16 18 20 22 24 Monday du Lund au to Vendred Frday 5h à 9h { 12h à 14h { 17h à 23h P2 { 0h 2 4 6 8 10 12 14 16 18 20 22 24 Saturday Le week end and Sunday 5h à 23h 17h à 23h P1 { P3 { 0h 2 4 6 8 10 12 14 16 18 20 22 24 Select P1 P2 P3 Meanng Te 1 program sets te Comfort temperature set pont n te mornng from 500 to 900 and from 1700 to 2300 n te evenng. Te 2 program sets te Comfort temperature set pont n te mornng from 500 to 900,at noon from 1200 to 1400 and n te evenng from 1700 to 2300. Te 3 program sets te Comfort temperature set pont on weeends from 500 to 2300. Customsable programs see pages 23 and 24. P4 P5 P6 Te customsable programs allow you to set set pont tme ntervals n te Comfort mode accordng to your needs. If no operatons usng te and eys are performed for 15 seconds, te dsplay returns to ts orgnal poston.
OPERATING MODE: CUSTOM PROGRAMMING - P4/P5/P6 : In ts mode, te eater operates n automatc daly mode at te Comfort or Setbac set ponts. To do ts 3 seconds RO Regardless of te current operatng mode - ress tese and eys smultaneously for 3seconds. Te screen wll dsplay «r». Pr Hr Ext P4 P6 P5 + - ress te or eys to select one of te customsable programs 4, 5 or 6 n te drop-down menu. We wll select te 4 program as an example. - Conrm by pressng te ey. See te example on page 22. ou can tus dene your own tme ntervals, eter n Comfort or n Setbac mode. See te example on te next page. By default, te factory settng for te 4/5/6 programmes s Setbac mode for te entre day.
HOW DO I CUSTOMISE THE PROGRAM? EXEMPLE - P4 For example for MONAY program L4, we ws to set te Comfort set pont temperature for 3 dfferent tme ntervals n te mornng from 600 to 900, at noon from 1100 to 1400 and n te evenng from 1800 to 2200 rs. Ex. 6:00 to 9:00 Select : nterval Result You are now customsng programme 4.See actvaton nstructons on page19 Interval 1 Cange te startng tme usng Cange te end tme usng Tme nterval 1 from 600 to 900 as been conrmed. You are now automatcally swtced to tme nterval 2. Ex. 11:00 to 14:00 Select: nterval 2 Result Interval 2 Cange te startng tme usng Cange te endtme usng Tme nterval 2 from 1100 to 1400 as been conrmed. You are now automatcally swtced to tme nterval 3. Ex. 18:00 to 22:00 Select: nterval 3 Result Tme nterval 3 from 1800 to 2200 as been conrmed. You are now returned to te ntal settng r. Interval 3 Cange te startng tme usng Cange te endtme usng You can now set te 5 or 6 program or select Ext to leave. Conrm wt. roceed n te same way for programs 5 and 6. You can eep te prevously dened program, or you can cange t. Conrm by pressng te ey and select Ext to leave. Ten conrm by pressng te ey. To cancel te programmng range, place te coce of our at «--». See page 23 for te cancellaton procedure. + Pr Hr Ext to ext P4 P6 P5
5.9 - Coordnatng the dsplays (thermostat/thermometer) : Exceptonally, under certan condtons, tere may be a temperature dsplay dfference between te eaters dsplay and te termometer dsplay. In suc a case, te two dsplays can be coordnated. Ts coordnaton s possble only f te unt s set between 17 and 23 C. All doors and wndows must be closed. Wat for te temperature to stablse n te room at least 6 rs. and as muc as possble, avod movements n te room. Te control termometer used for measurng te temperature must be placed n te centre of te room at a egt of 120 cm 48 n from te oor. o not place t n a at poston on te furnture. Wt te termostat n COMFORT mode, pressng te ey for 3 seconds wll provoe one of te followng two states 1 - Flasng dsplay of te set pont temperature, n wc case coordnaton s possble. Mae te canges usng te and eys Conrm by pressng te ey. Or, 2 - splay of «NON» message coordnaton s not possble you ave to wat for te temperature to stablse. If no operatons usng and eys are performed for 15 seconds, te dsplay returns to ts orgnal poston. Cancel a programmng range n a personnalzed program. - ress smultaneously for tree seconds on te and eys. «r» wll sow on te screen. - ress on te and eys to select te program to be elmnated ex 4. - Conrm by pressng on. «E» sould appear. - ress on te and eys untl «- - H» appears. Conrm by pressng on. - Carry out te same procedure by redenng your programmng ranges 2 and 3 or by cancellng te range. - To ext, press on or untl «Ext» appears. Conrm by pressng on.
Ts eater s eupped wt an automatc reset overeat protecton. In case of a malfuncton of te unt bloced ar output or ntae, te eater wll stop eatng automatcally. To reset te eater Cec tat te front panel, top and bottom of te eater are free of obstructon. Once te obstructon s removed and te eater cools down, te overeat control wll reset automatcally.
NEVER USE ABRASIVE OR ACETONE-BASED PRODUCTS TO CLEAN YOUR HEATER AS THIS MAY DETERIORATE THE EPOXY FINISH. ANY REPAIR ON YOUR CONVECTAIR HEATER SHOULD ONLY BE DONE BY A QUALIFIED TECHNICIAN, AND ONLY AFTER THE HEATER HAS BEEN DISCONNECTED. Recommendatons and advce Your CONECTAIR eater wll become ot wen n use. Cauton s advsed wen young cldren are present. o not nsert small obects n te eater ts could cause an electrcal sort crcut, re or damage to te nner components. Any use or modcatons not approved by CONECTAIR may cause electrcal sort crcuts, re or nures to te users. In certan cases, t s possble for yellowng of te surface to occur over tme. Ts s not due to a manufacturng defect.ts s caused by surroundng ar, wc may contan smoe or dust, beng eated and crculated troug te eater. Ts s partcularly te case wt wte eaters and may translate n an mportant mportant colorng of te unt. Preventon : t s suggested that surfaces be frequently cleaned especally wth unts nstalled n bathrooms, ktchens, locatons where cgarette smoke s present, rooms wth a replace or wood stove. Never use ths heater durng constructon work or other actvtes that generate a lot of dust.
PROBLEM CHECK ACTION Mae sure tat te dgtal dsplay s actve. ress ress successvely on te untl te Comfort settng s dsplayed. If te dgtal dsplay stll does not turn on. Mae sure tat te system crcut breaers are functonal and press. Te unt does not eat. Mae sure tat te Comfort mode s on. ress successvely on te untl te Comfort settng s dsplayed. Mae sure tat te Open Wndow functon s not enabled and tere are no open wndows or doors n te room. Close te door and/or wndow and reset te functon by pressng. Te dgtal dsplay s on, te eatng ndcator s off. Cec te set pont value. Te room temperature reures no eatng. Te unt s n Setbac mode ECO. Te unt eats all te tme. erfy tat te temperature settng as not been canged. erfy tat te unt s not located near an open door and/or n a draugty place. Reset te temperature. Close te door or elmnate te draugt. Te unt does not follow te programmng commands. erfy tat t s n programmng mode. Cec te programmng mode. Set te unt n programmng mode. erform programmng. Te eater does not wor. erfy tat code 0801 s dsplayed on te screen. IN ALL OTHER CASES, CONTACT CONVECTAIR. 1 800 463-6478 support@convectar.ca OR the nearest Servce Center. nplug te eater from te electrcal crcut for 24 ours. Once ts tme as passed, replug te eater. If te problem perssts, contact CONVECTAIR.
IDENTIFICATION LABEL IMPORTANT : PRODUCT INFORMATION APPEARS ON THE HEATER S IDENTIFICATION LABEL. Te dentcaton label s located on te bac of te eater. It ncludes - Te complete model number, capacty, colour A and ts producton reference number tat must be ncluded n any warranty clam. - Capacty B. - Standard certcaton C. B A Made n France 7733-C20-FS 2000W - 240V~ 60Hz Constructeur N 412 C D WEEK / YEAR N OF 150707 2 years aganst all defects / 5 years on heatng element. All CONVECTAIR eaters are subects to a double warranty. Warranty s applcable from date of purcase by te customer and under certan specc condtons. All detals furnsed wt eac eater. lease eep your nvoces purcase and / or nstallaton. To regster your product warranty you may ll out te form avalbale on our webste OR by ll out te paper form ncluded wt te eater. nautored modcaton of te eater wll contravene wt te product warranty. SERVICE CENTERS : Contact CONVECTAIR to nd the closest servce center: Toll-free : 1 800 463-6478 Webste : www.convectar.com 30, carré Scard, Sante-Térse uébec, CANAA 7E 36 one 450 433-5701 Fax 450 434-3166 Emal supportconvectar.com www.convectar.com 28