TECHNICAL MANUAL CQUBE Your Dealer EN Rev. 110830
1. Contents. Technical manual. CQUBE 1. Contents page. 2 2. Overview Technical service card 3 3. Maintenance and care of grinder 4-8 4. Cleaning with GRINDZ 9 5. Warning message shown in display 10-12 6. Error code description 13-14 7. Brewing cycle settings 15-17 8. Electrical sheme 18 8. Electrical sheme UC and IO Pay card 19 8. Electrical sheme High current 20 9. Exploded view 21-42 10. Spare parts list 22-43 11. Dimension sketch 44 12. Overview of components, cold water 45 12. Overview of components,cold water + CO2 46 13. Service intervals 47 2.
2. Overview: Technical Service Card CQUBE TECHNICAL SERVICE CARD. TECHNICAL SERVICE CARD Item number: 1602693. Is used for cleaning and setting jug beverages. The user card is supplied by your dealer. For complete menus See Programming manual. Insert the card with the chip upwards, according to the illustration. The display will show the Service Menu, Jug Beverage and you can now browse forwards through the menu. Service Menu Jug Beverage To use the machine again. Remove the card and keep it in a safe place. 3.
3. Maintenance and care of grinder EK21 CQUBE bean container Bean valve Grinder Grinder dispenser 4.
3. Maintenance and care of grinder EK21 CQUBE 1. Periodic maintenance. grinder EK21 - Each month: Clean silicon outlet, grinding house and grinding discs. - Monthly cleaning of grinder using GRINDZ cleaning tablets (item no. E1001001). - In case of blockage: cleaning, if necessary detaching of rotating carrier. 2. Safety Please read and observe the following service instructions carefully. Non-observance can result in damage to the grinder as well as in healththreatening risks for the user. All installations shall been done by an qualifi ed personnel. 2.1 Symbols Safety instruction: In case of non-observance, extreme risk of accidents exists. General instruction In case of non-observance, the device can become damaged or optimum operation not be guaranteed. 2.2 Safety instructions The grinder is only allowed to be used to grind whole coffee beans. Ground coffee is never allowed to be fi lled into the input-shaft. Do not carry out any modifi cations or changes on the grinder. In case for non-observance, the manufacturer shall be liable for resulting damain no case whatsoever. Never put your fi ngers or objects into the rotating grinding mechanism inside the input-shaft.the grinder must not be operated when turning parts are accessible! Make sure, that the power cannot be turned on when working on the built-in grinder! In order to avoid damages, do not use power tools or cordless electric screwdrivers for any work on the grinder. 5.
3. Maintenance and care of grinder EK21 CQUBE 3. Every month. Approximately every month the grinder housing and spout should be inspected for coffee residues and obvious damages. In case of too much coffee residues around the spout, check if the silicone flapper inside the spout is in place. Proceed as follows: 3.1 Remove bean container. Remove all coffee residues from the spout and the grinder housing by grinding through all coffee beans and using a vacuum cleaner to remove all residues. 3.2 Remove the three Allen screws (A) in the grinder housing lid. 3.3 Carefully detach the grinding housing. Fig.1. Note its position for correct reassembly. Do not alter the adjustment of the grinding discs. A Fig.1. 3.4 Clean the inside of the grinder housing and the outside of the disc carrier with a soft brush. Check the correct position of the silicon flapper and the spout. (see chapter 6 and 6.5) 3.5 When reassembling the grinder housing, again check for the correct position and do not alter the grind adjustment of the discs. Fasten the three Allen screws. 4. Removing the rotating carrier. Each third year or after 50000 cups the grinding discs should be exchanged to guarantee constant grinding capacity and accurate dosing. Proceed as follows: 4.1 Remove the grinder casing and the rotating carrier. Loosen the left threaded nut by turning it clockwise (A ) Fig. 2. 4.2 Remove the worn-out grinding discs by detaching the slotted screws. (B) Fig.2. B Fig.2. A 6. B
3. Maintenance and care of grinder EK21 CQUBE 4. Removing the rotating carrier. (continuation). 4.3 Clean the surfaces of the seats and the new discs. In case of coffee residues left between disc carrier and new disc, the discs will not run parallel and the grinding performance will deteriorate. 4.4 Mount the new rotating grinding disc.note! The grind adjustment has to be modified after changing the discs. See chapter 5 for new basic adjustment. 5. Basic adjustment of the grinding finess. 5.1 Loosen grinder housing. 5.2 Press the adjustment screw while turning it clockwise until the milling blades touch. Check that they are touching by turning the container manually. The blades are touching when you hear a scratching sound. Fig.3. C C C C Fig.3. 5.3 Press and turn the adjustment screw counterclockwise 20 notches for the basic setting (approx. 0.5 mm). 5.4 Reassemble grinder house. 6. Exchange of the silicone flapper in the spout. If the silicon fl apper is damaged or out of place it has to be replaced respectively refi tted to the housing. Proceed as follows: 6.1 If possible: remove coffee residues (close bean container, grind empty, vacuum cleaner). 6.2 Loosen the set screw at the front of the grinder housing. Fig.4. 7.
3. Maintenance and care of grinder EK21 CQUBE 6. Exchange of the silicone flapper in the spout. (continuation). Fig.4. Fig.5. E D F 6.3 Carefully pull out the spout. (D).Fig.5. 6.4 Take out silicone flapper (E) which is placed in a groove inside the spout bore, put in the new silicone flapper 6.5 Reassembling the spout (D) and silicone flapper (E) by bringing pressure on the spout tube to make sure that the silicone flapper (E) will be fixed correctly. See Fig.4. 7. Correction of the adjustment. In case that the fi neness of the ground coffee should be changed, the adjustment shaft is accessible through a bore from the front of the grinder housing. 7.1 Press and simultaneously turn the adjustment bolt anticlockwise one or two notches for coarser coffee grounds 7.2 Press and simultaneously turn the adjustment bolt clockwise one or two notches for finer coffee grounds. 7.3 After performing the grind adjustment, run 2-3 cups of coffee through in order to achieve the current settings. 1 1 2 3 4 1 = Screw driver 2 = Adjustment bolt 3 = Adjustment pinion 4 = Locking pin 8.
4. Cleaning with GRINDZ cleaning tablets. Every month 3. Cleaning with GRINDZ cleaning tablets, Every month (Product no. E1001001) Do the following: Open the door. Remove the brewer (in connection with rinsing) and close the lid on the bean canister. Insert card in the card reader, scroll to HARDWARE TEST and press enter, then scroll to canister 1. 1. Start the grinder by pressing Enter. 2. Run until no more coffee grinds come out of the grinder. 3. Remove the bean canister and fi ll with one cap full of GRINDZ tablets. 4. Re-place the bean canister. 5. Start the grinder by press the Enter button. (To stop grinder press Enter button.) 6. Run until no more cleaning powder come out of the grinder. 7. Open the lid of the bean canister and press the Enter button for coffee. 8. Reassemble the brewing mechanism. Tips: Keep a cup under the grinder outlet during the cleaning process. 9.
5. Warning message shown on display CQUBE Message on display: Display shows Hardware Error: Not available Heating Water Please Wait... Low Water Level Press Enter Key Filling Water Please wait Hardware error Drink cannot be selected as pot. Low temperature in the water tank, the machine is heating up (blocked) Low water level in water tank. The machine is fi lling water. Select Product Temp: Strength: Jug Beverage Jug Mode Cups: Energy save mode Can Empty Warning Low Temperature Low Temperature Blocked Empty Drip Tray Energy-saving mode Concentrate is empty The temperature is low, it is still possible to dispense drink. The temperature is low, the machine is blocked. The drip tray is full of water Overcurrent Water Level 10.
5. Warning message shown on display CQUBE Message on display: Display shows Unknown Error Low Water Level Blocked Can Empty Blocked Heating Water Open Brewer Check Water Supply Empty Wastebox ERROR Level Pins Change Brewer Filter Place Cup Bev. Disabled Please Wait... Clean Filter Cleaning Hot Key Unknown error The water level in the water tank is low, it is not possible to dispense drink. Out of concentrate, Blocked Temperature low Open brewing mechanism The water has not reached the correct level in the water tank. Check the water tap, restart the machine. The waste box is full, open the door and empty out the grounds. When you close the door, press E to reset the counter. Selectable in main programme. Check, Level sensor. The brewing fi lter is clogged. The fi lter needs replacing or cleaning. If the cup sensor has been activated, this is shown if no cup has been placed on the drip tray. The drink has been disabled. Please wait Clean fi lter Clean. panel active Door Open 11.
5. Warning message shown on display CQUBE Message on display: Display shows Change Water fi lter The water fi lter needs replacing; press the E button to reset the counter. Open Door Open door Fill clean. agent Load Detergent Load Detergent Load clean. agent Close door Close Door Place Jug Place pot Press Enter Enter To Start Cleaning Brewer Clean brewer mech Time remaining Time Left Rinsing Brewer Rinsing brewing mech Cycles left: Cycles Left Cleaning Paused Cleaning paused Close door Close Door Please Wait... Please wait 12.
6. Error code description. CQUBE Error code description: Overcurrent Group 1:1 = Brewing unit (0,95A limit) Group 1:2 = Other components (Fan, Valves, Relays Etc..) (1,5A limit) Group 1:3 = Mixer 1 (3,5A limit) Group 1:5 = Mixer 2 (3,5A limit) Message is shown if one of the software fuses have been trigged. Caused by a component using too much current (A). You can run each component in the Hardware Test menu and the message will show when you turn on the component that is using too much current. ERROR: Water Supply Message will show if the inlet valve has been open for more than 3 minutes and the machine still have not acquired correct water level Action: Check that the water to the machine is turned on, Check the levelsensor, test function of the inlet valve in Hardware Test ERROR: Tempsensor Message will show if the NTC sensor is broken or is out of range of its resistance curve, also if cables have loosened from its connectors. Action: Replace NTC sensor, check cable connection on the NTC and PCB board. ERROR: Levelpins Message will show if the cables to the water level high & low have been connected to the wrong levelpin. Action: Swap cables to the levelsensor ERROR: Check Heater Message will show if the machine have not reached working temperature within 14 minutes from startup. Action: Check Overheating protection, cables to the element, solid state relay, signal from IO-board to solid state when you know the machine should heat, you can also force the element to run in Hardware Test. ERROR: BREWER C.Door press E Message will show when you interrupt a brewing cycle, eg. open the door when the machine is producing coffee. The machine needs to reach home-position before producing new drink. Action: Press E, check door sensor, brewmec sensor Clean brewfilter Message will show if the brewer motor uses more than 0,95A Action: Check brewfi lter if clogged, brew chamber is mounted in wrong position, brewer motor is broken. 13.
6. Error code description. CQUBE Error code description: Peripheral Hardware Error This message will appear if you have loaded a faulty recipe into the machine, the IO-Board is broken and does not get connection with the UcMerisc board. Usually this message appears if you eg. have loaded a standard recipe into a machine using pay system. Make sure you are using the right recipe and reload. Memory Error: Reload Recipes There is no recipe loaded on the UcMersic board. Transfer of the recipes have been interrupted and not completed in UcLoader. memory on the UcMersic board is broken. Fatal Error Contact Service Multiple Overcurrent messages at the same time, or shortcut on the IO-Board, try to run components in Hardware Test and locate faulty components, replace the IO-Board if no one is found. Smartcard Error: Unknown Card The smartcard is not programmed, chip on the smartcard is damaged, card reader is broken or broken cable between card reader and UcMerisc board. Action: Insert and remove the card repeatedly, if the message is shown every time, try another card. If the error remains replace the card reader. Smartcard Error: Wrong Pincode Chip on the smart card have been damaged, replace card Pay Error Type XXX IO-Pay board is reporting error from the payment device, check coinchanger or cashfl ow device. 14.
7. Brewing cycle settings CQUBE Brewing cycle settings: Aeration - Sum of sections from position 1 to 3 = 100% - Adjustment in % (0-100%), applies to sections from position 2 to 3 - Affects stirring in coffee bed > Taste: Acidity Pre brew - Pause at section between positions 1 and 3 - Adjustment (0-10 sec) at step in 0.1 sec - Affects the amount of acid from stirring> Taste: Acidity Extraction - Pause between positions 2 and 4 - Adjustment (0-20 sec) at step in 0.1 sec - Affects total contact time > Taste: Body Press time - Sum of sections from position 3 to 5 = 100% - Adjustment in % (0-100%), applies to sections from position 3 to 4 - Affects the consistency of the grounds > Cleanliness - Affects the strain on plunger and cylinder > Operating reliability: Vacuum pressure in cylinder Decompress time - Pause between positions 3 and 5 - Adjustment (0-10 sec) at step in 0.1 sec - Affects the consistency of the grounds > Cleanliness - Affects the strain on plunger and cylinder > Operating reliability: Vacuum pressure in cylinder Empty time - Pause between positions 5 and Home position - Adjustment (0-10 sec) at step in 0.1 sec - Affects the amount of fi nished coffee that comes out of the cylinder > Cleanliness / Operating reliability After Empty time the brewing continues until the micro switch is activated - Home position 1 2 3 Home Position Pre brew Extraction 4 5 Decompress 15. Emptytime
7. Brewing cycle settings CQUBE REMEMBER For fresh brew machines, the coffee should have the coarsenessautomatic grinding. Grinder settings for automatic grinding are: grinding blades together and set 8 steps back. The optimal total contact time between water and coffee for automatic grinding is 30 sec. The basic settings for coffee were defi ned in cooperation with ECBC in Oslo, to ensure quality in the cup. Water amount 170 ml (before contact with coffee) Coffee amount 11 g (requires above grinder settings) Aeration 70% Pre brew 3.8 sec Extraction time 11.5 sec Press time 50% Decompress time 2.0 sec Empty time 6.0 sec TIPS To compensate for lower Aeration (higher %) Pre brew can be increased to a certain degree. Increased Pre brew time means that more water and coffee are added before the plunger reaches the top position. This produces a better blend. Adjust Pre brew in steps of 0.1-0.2 sec at a time; this quickly provides results in terms of taste. Varies for different coffee types, however. Increased Extraction time produces more body, but only to a certain degree. Too much time makes the coffee over-extracted, which produces a very bitter taste. To little Extraction time means the coffee is under-extracted, leaving little aftertaste. If you wish to cut down on the total brewing cycle time, you want the taste to undergo minimal change. If you shorten the Extraction time, you can compensate somewhat by either putting the grinder on a fi ner coarseness setting or increasing the coffee dose. You then have to test the coffee carefully, to make sure it is not too strong. When you have tasted several cups of coffee, it is very easy to misjudge the taste. For increased dose, the taste is very accurate when you swallow, but the aftertaste disappears and instead it is harsh on the throat. If you increase the volume too much, the grounds can become soaked. To fi x this, you must increase the Press time. This causes the plunger to lower more before the pause (position 3-4); the result is a higher vacuum effect in the cylinder and more fi nished coffee is sucked out through grounds. At the same time, you should increase the Decompress time, to allow the coffee to penetrate the fi lter before empty position is reached and the vacuum pressure in the cylinder is released. Remember to increase the Empty time so all the coffee can drain out of the cylinder. 16.
7. Brewing cycle settings CQUBE SYMPTOM - CAUSE - SOLUTION SYMPTOM CAUSE SOLUTION The water and coffee splash out of the brewing chamber during the aeration process. The coffee either lacks or has too much character. The grounds are very soggy or almost watery when the brewer opens. The brewing mechanism sounds very strained. - Hard water. A high surface tension makes it diffi cult for the coffee to absorb water. - Very fresh coffee often takes a little longer to absorb water - The acidity setting is too low/high. - The coffee is too old. - The fi lter is clogged. - The water is hard. A high surface tension makes it diffi cult for the coffee to absorb water and for the water to pass through the fi lter. - Very fresh coffee often takes a little longer to absorb water - The coarseness setting is too fi ne. - Coffee dose is too high. - The volume setting is too high. - The brewing chamber may be cracked. - The cylinder may be cracked. - The fi lter is clogged - The coarseness setting is too fi ne. - The coffee dose is too high. - The brewing mechanism setting needs adjustment. - Run the cleaning programme and replace the fi lter if necessary. - Lower the Aeration %. Test a cup. Increase the Pre brew to compensate if necessary. - Run the cleaning programme and replace the fi lter if necessary. - Increase the Pre brew setting if the coffee lacks character/acidity. 0.1-0.2 sec makes a very big difference. - Lower the Pre brew setting for the opposite effect. - Empty the canister and grinder, clean and refi ll coffee. - Run the cleaning programme and replace the fi lter if necessary. - Increase the extraction time if necessary. - Increase the Press time and/or Decompress time if necessary. - Check grinder setting /clean. - Check the Strength setting. - Check the Volume setting. - Inspect the brewing chamber for cracks. - Inspect the cylinder for cracks. - Run the cleaning programme and replace the fi lter if necessary. - Check grinder setting /clean. - Check the Strength setting. - Remove the brewing mechanism, rotate, adjust according to the manual instructions. The grounds scraper cannot remove all the grounds. The grounds scraper is still on one side of the brewing chamber during the brewing cycle. - The brewing mechanism setting needs adjustment. - The grounds scraper is damaged. - The brewing chamber is incorrectly installed. - Remove the brewing mechanism, rotate, adjust according to the manual instructions. - Replace the grounds scraper. - Remove the brewing mechanism, rotate until it opens, pull out and insert the brewing chamber. Check that it follows the cycle. 17.
8. Electrical diagram. CQUBE 18.
8. Electrical diagram. UC Pay 19.
8. Electrical diagram. High Power Connection 20.
9. Exploded view. Door / Front CQUBE 1 6 2 3 4 5 20 19 18 17 16 15 14 13 7 12 8 11 9 10 21 22 21.
10. Spare parts list. CQUBE Description; Art. no. Pos. no. Amount/unit Valid for page 21 Door / Front Bean container window (high) 1105530 1 1 Bean container window (low) 1105531 2 1 Top Lid 1105533 3 1 Frame for card reader 1505035 4 1 Card Reader 1602697 5 1 Slide latch 1202495 6 3 Chrome ring 1105532 7 2 Outlet drip tray 1105534 8 2 Drip tray 1105528 9 1 Drip tray insert 1102035 10 1 Drip tray extension 1105529 11 1 Spiral 120229 12 2 Cup stand 1102036 13 1 Light emitting diode white 1608708 14 1 Light emitting diode red 1608710 15 1 Cup sensor 7140011 16 1 Outlet angled 1201415 17 1 Display 1604122 18 1 Lock with nut 120253 19 1 Fastener for circuit board 1203416 20 4 User Card (green 1602692 21 1 Technical Service 1602693 22 1 22.
9. Exploded view. Machine CQUBE 7 8 1 21 2 5 4 12 24 Säkring 5 AT 3 6 11 13 15 16 19 17 26 25 20 23 18 14 22 23.
10. Spare parts list. CQUBE Description; Art. no. Pos. no. Amount/unit Valid for page 23 Machine Brew mechanism 710075 1 1 Electronic card IO - TE 1604111 2 1 Fuse 5A T 1604384 -- 3 Power supply 150W 1031652 3 1 Front, bean container high 1105498 4 1 Front, bean container low 1105499 5 1 Centrifugal Fan, 24V 0,24A 1604151 6 1 Lid bean container 1105497 7 1 Frame for lid, bean container 1105496 8 1 Grinder 1604752 11 1 Relay 1pol 160243 12 1 Socket 160246 12 1 Capacitor 12 μf 832392 12 1 Main socket 160570 13 1 Power cord Europe 160565 14 1 Valve double 2,5L/min. 1206281 15 1 Centrifugal Fan, 24V 0,18A 1604152 16 1 Connector 160549 17 1 Waste box 1105359 18 1 Switch 2 pol. 160801-04 19 1 Inlet hose 150541 20 1 Micro switch 710070 21 1 Waste funnel 1105357 22 1 Waste box base cabinet 1105317 23 1 Solid state 1604201 24 1 Lock complete (door) 120253 25 1 Key, (door) 1202531 26 2 Options: Water fi lter + patron complete. 1505360-1 Filter head 1505362-1 Filter cartridge 1505361-1 24.
9. Exploded view. Tank CQUBE 1 9 10 8 11 2 19 7 6 12 13 14 5 15 3 16 20 18 17 4 25.
10. Spare parts list. CQUBE Description; Art. no. Pos. no. Amount/unit Valid for page 25 Tank Tank complete 7140019 1 1 Water tank 5L + lid 260141 2 1 Insulation for refrigeration unit 1201292 3 1 Insulation bottom 120131 4 1 Outlet valve 24V 1206289 5 1 Seal for outlet valve 1561010 6 1 Element 2200W 1601311 7 1 Gasket water tank 1561012 8 1 Double seal level sensor 1605362 9 1 Sensor pin, short 1205302 10 1 Sensor pin, long 1205301 11 1 Steam hose 1561015 12 1 NTC compl. belong 711000 13 1 Seal for NTC thermistor 1605361 14 1 Drainage tube 1561007 15 1 Inlet hose 1561014 16 1 Motoraxle for motor gear 1604614 17 3 Motor gear, without axle 1604612 18 3 High limit control 220220 19 1 Silicone hose (sales by metre) 150501 20-26.
9. Exploded view. Mixing system CQUBE 2 4 9 silicone hose sales by metre 14 3 14 1 13 1 1 5 6 7 8 10 11 12 27.
10. Spare parts list. CQUBE Description; Art. no. Pos. no. Amount/unit Valid for page 27 Mixing system Hose adaptor, mixing system 1604836 1 5 Outlet brew mechanism 1201416 2 1 Outlet brew mechanism, extension 1201417 3 1 Outlet angled 1201415 4 3 Hose brew mechanism - fan 1505034 5 1 Hose mixing bowl - fan 1505033 6 1 Valve double outlet, CO2 1104525 7 1 Valve double outlet, cold water 1104534 8 1 Brewing motor complete 1201432 9 1 Brewer dock white 120144 10 1 Pin 3,5x36 1201453 11 1 Pin 2,0x36 1201454 12 1 Micro switch V5J (FB brew engine) 160829 13 1 Silicone hose (sales by metre) 150501 14-28.
9. Exploded view. Mixing bowl CQUBE silicone hose sales by metre 3 4 5 12 6 7 2 1 11 10 9 8 29.
10. Spare parts list. CQUBE Description; Art. no. Pos. no. Amount/unit Valid for page 29 Mixing bowl Angle for mixing bowl 1206705 1 2 Mixing bowl 1206704 2 2 Steam trap 1206707 3 2 Bulkhead adaptor 1206706 4 2 O-ring 120638 5 2 Motor whipper plate 1604592 6 2 Whipper motor 24V Complete 7001111 7 2 (incl. slinger disc, motor whipper plate) Slinger disc 1604804 8 2 Mounting plate 1206702 9 2 Grommet for whipper pin 120655-02 10 2 Whipper 1206703 11 2 Silicone hose (sales by metre) 150501 12-30.
9. Exploded view. Water + CO2 CQUBE water + CO2 8 6 6 9 8 17 7 10 18 16 19 15 4 2 12 13 14 3 11 1 5 31.
10. Spare parts list. Chiller unit water + CO2 CQUBE Description; Art. no. Pos. no. Amount/unit Valid for page 31 P 146 Chiller unit 1104801-1 Compressor ELECTROLUX GD 40 MB 1104580 1 1 Clixon for GD40MB 1104581 2 1 Start capacitor for GD40MB 1104582 3 1 Startrelay for GD40MB 1104583 4 1 Condenser 101150 1104584 5 1 JG PM060806E 1104585 6 3 Non return valve 1104586 7 1 JG PM090612E 1104587 8 2 JG PM0208E 1104588 9 1 JG SM030808S 1104589 10 1 Filter dryer 1104590 11 1 Fan motor ALEXMAR 5W 1104591 12 1 Fan blade 1104592 13 1 Fan holder 1104593 14 1 Thermostat RANCO K50 L1319 1104594 15 1 Motorpump 1104605 16 1 Solenoid valve 1104598 17 1 JG PM4508F4S 1104599 18 1 Electronic box 1104601 19 1 32.
9. Exploded view. Chiller unit in machine CQUBE Chiller unit, water 1 5 10 9 2 6 4 7 3 8 33.
10. Spare parts list. Chiller unit water CQUBE Description; Art. no. Pos. no. Amount/unit Valid for page 33 Chiller unit, cold water 1104802-1 Start capacitor for GD 40 MB 1104582 1 1 Thermostat K-50 L3019 1104594 2 1 Filter dryer 10g 6,2-2,5 1104590 3 1 Condenser STFT 10215 MINI 1104609 4 1 Clixon 1104581 5 1 Fan SUNON MBT 1104611 6 1 Cooling block 1104612 7 1 JG corner 8x8 (1037) 1104613 8 1 Relay 1104583 9 1 Compressor GD 40 MB 1104580 10 1 34.
9. Exploded view. Grinder EK21 CQUBE 18 13 14 12 11 8 1 9 10 20 22 19 23 21 17 16 15 7 3 6 4 5 2 24 35.
10. Spare parts list. Grinder EK21 CQUBE Description; Art. no. Pos. no. Amount/unit Valid for page 35 Grinder Inlet housing 838916 1 1 Slotted pan head screw - M4x12 838753 2 1 Adjustment shaft 837992 3 1 Adjustment pinion 837991 4 1 Pressure spring 838709 5 1 Allen set screw - M5x10 839230 6 1 Slotted cylinder head screw M4x50 838704 7 3 O-ring 839252 8 1 Worm shaft 837863 9 1 Allen screw M4x4 - stainless steel 838869 10 1 Grinding disc carrier 837985 11 1 Fixed grinding disc 837247 12 1 Grinding disc carrier - rotating 838141 13 1 Rotating grinding disc 837248 14 1 Pan head screw DIN 85 M5x8 835579 15 4 Washer DIN 433-10,5 stainless steel 839261 16 1 Hexagon nut left-hand thread 838642 17 1 Grinding housing 839259 18 1 Allen screw DIN 912 - M4x45 838876 19 3 Outlet tube, metal 839260 20 1 Allen set screw DIN 916 - M4x10 836503 21 1 Outlet hose, grinder FB + hose clamb 710083 22 1 Silicone disc 839471 23 1 Motor 837932 24 1 36.
9. Exploded view. Brewing mechanism CQUBE 17 18 19 20 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 37.
9. Exploded view. Brewing mechanism CQUBE 29 30 33 34 35 36 37 38 39 28 31 40 32 41 42 43 27 26 25 24 23 22 21 38.
10. Spare parts list. Brewing mechanism CQUBE Description; Art. no. Pos. no. Amount/unit Valid for page 37 brew mechanism Defl ector, Cylinder 4720008 1 Pin, Crank Arm 4720010 2 O-ring piston 4720012 3 Rubber ring piston 4720013 4 Tefl on seal 4720014 5 Plate, Top 4720015 6 Screw, 8 x 1/2, Truss 4720016 7 Cylinder 4720017 8 Plug, vent, Cylinder 4720018 9 Screw, 4-40 x ¼, 4720019 10 Screw, 8-32 x ½, 4720020 11 Assembly Filter 47200213 12 Seal, Brew Chamber 4720022 13 Bar, Latch 4720023 14 Carriage, Wiper 4720024 15 Rod, Carriage, Wiper 4720025 16 Retaining Ring,.250 4720026 17 Wiper, Complete 4720027 18 Brew Chamber 4720028 19 Spring Clip, Latch Bar 4720029 20 Valid for page 38 brew mechanism Housing, Vertical Rod 4720001 21 Cam, Triple 4720002 22 Unwipe Arm Assembly 4720003 23 Spacer, Wipe Arm 4720004 24 Spring, Wipe Arm 4720005 25 Retaining Ring,TRU ARC 4720006 26 Vevarm 4720007 27 Plate, Ret., Cycle 4720030 28 Plate, Ret., Support 4720031 29 Latch, Block, LHS 4720032 30 Latch, Block, RHS 4720033 31 Retaining Ring 4720034 32 Tube, Outlet, Water 4720035 33 Wrap, Brew Chamber 4720036 34 Shim 0,2 1303501 35 Shim 0,5 1303502 36 Spacer, Sil., 3/16 x.350 x 1.5 4720038 37 Spring, H-Frame 4720039 38 H-Frame 4720040 39 Screw, 8-32 x 3/4, PAN 4720041 40 Pin, Grooved, 3/16 x 1.25 4720046 41 Wipe Arm, Assembly 4720048 42 Vertical Rod, Welded 4720049 43 39.
9. Exploded view. Canisters high/low CQUBE 3 4 4 4 1 2 5 5 5 6 40.
10. Spare parts list. high/low CQUBE Description; Art. no. Pos. no. Amount/unit Valid for page 40 Canister high 160 x 400 1204964 1 1 Canister high 67 x 400 1204965 2 3 Lid for 160 canister 1204952 3 1 Lid for 67 canister 1204953 4 3 Concentrate pipe left 120489 5 3 Concentrate pipe right 120493 6 1 Canister low 160 x 400 1204887 1 1 Canister low 67 x 250 1204962 2 3 Lid for 160 canister 1204952 3 1 Lid for 67 canister 1204953 4 3 Concentrate pipe left 120489 5 3 Concentrate pipe right 120493 6 1 41.
9. Exploded view. Bean container/ canisters high/low CQUBE 1 2 2 2 3 4 4 5 42.
10. Spare parts list Bean container/ canisters high/low CQUBE Description; Art. no. Pos. no. Amount/unit Valid for page 42 Bean container high 1105494 1 1 Canister high 67 x 400 1204965 2 3 Lid for 67 canister 1204953 3 3 Concentrate pipe left 120489 4 2 Concentrate pipe right 120493 5 1 Bean container low 1105495 1 1 Canister low 67 x 250 1204962 2 3 Lid for 67 canister 1204953 3 3 Concentrate pipe left 120489 4 2 Concentrate pipe right 120493 5 1 43.
11. Dimension sketch. CQUBE Model CQUBE M CQUBE L A 879 mm 995 mm B 420 mm 420 mm C 565 mm 565 mm 44.
12. Overview of components Cold Water CQUBE Water IN Water OUT Thermostat Fan Compressor Cooling block Condenser Dryer 45.
12. Overview of components Water + CO2 CQUBE Water IN Cooling block Carbonated water OUT Pump pressure increase Electronic box Fan Condenser Carbon acid IN Compressor Water OUT Dryer Solenoid valve Thermostat Gas holder Carbon dioxide tube 46.
13. Service intervals. CQUBE 47.
FOR SERVICE Please contact Your dealer......... CREM International AB Box 10, Viksgränd 2, SE-670 40 Åmotfors, Sweden Tel: +46 (0)570-477 00, Fax: +46 (0)570-47719 E-mail: info.se@creminternational.com www.creminternational.com Art. nr/art. no. 1740067