FOR HOUSEHOLD USE ONLY

Français English Italiano ISTRUZIONI PER L'USO OPERATING INSTRUCTIONS MODE D EMPLOI INSTRUCCIONES PARA EL USO Español LEGGERE ATTENTAMENTE QUESTE ISTRUZIONI D'USO PRIMA DI UTILIZZARE LA MACCHINA. READ THESE OPERATING INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE. LIRE ATTENTIVEMENT CETTE NOTICE AVANT D UTILISER LA MACHINE. LEER ATENTAMENTE ESTAS INSTRUCCIONES DE USO ANTES DE USAR LA MÁQUINA. FOR HOUSEHOLD USE ONLY USAGE DOMESTIQUE SEULEMENT Type Sin017XNI Ideas with Passion

Fig.1 Fig.2 Fig.3 Fig.4 Fig.5 Fig.6 Fig.7 Fig.8 Fig.9 Fig.10 Fig.11 Fig.12 2

Fig.13 Fig.14 Fig.15 Fig.16 Fig.17 Fig.18 Fig.19 Fig.20 Fig.21 Fig.22 Fig.23 Fig.24 3

Fig.25 Fig.26 Fig.27 Fig.28 Fig.29 Fig.30 Fig.31 Fig.32 Fig.33 Fig.34 Fig.35 Fig.36 4

Fig.37 Fig.38 Fig.39 Fig.40 Fig.41 Fig.42 Fig.43 Fig.44 Fig.45 Fig.46 Fig.47 Fig.48 5

IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against fire, electric shock and injury to person do not immerse cord, plugs, or machine in water or other liquid. 4. Close supervision is necessary when the appliance is used by or near children. 5. Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance. 6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment. 7. The use accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or injury to persons. 8. Do not use outdoors. 9. Do not let cords hang over edge of table or counter, or touch hot surfaces. 10.Do not place on or near a hot gas or electric burner, or in a heated oven. 11.Always attach plug to appliance first, then plug cord into wall outlet. To disconnect, turn any control to off, then remove plug from wall outlet. 12.Do not use appliance for than intended use. 13.Save this instructions. SAVE THESE INSTRUCTIONS 16

INSTRUCTIONS FOR THE POWER SUPPLY CORD A. A short power-supply cord (or detachable power-supply cord) is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord. B. Longer detachable power-supply cords or extension cords are available and may used if care is exercised in their use. C. If a long detachable power-supply cord or extension cord is used, 1. The marker electrical rating of the detachable power-supply cord or extension cord should be at least as great as the electrical rating of the appliance 2. If the appliance is of the grounded type, the extension cord should be a grounding-type 3-wire cord, and 3. The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over. English 17

1 GENERAL INFORMATION This coffee machine is made for brewing espresso coffee and features a swivel steam and hot water spout. The controls on the front side of the machine are labeled with easy-to-read symbols. The machine has been designed for domestic use and is not suitable for professional, continuous use. Warning. No liability is held for damage caused by: Incorrect use not in accordance with the intended purposes; Repairs not carried out in authorized service centers; Tampering with the power cord; Tampering with any parts of the machine; Use of non-genuine spare parts and accessories; Failure to descale the machine or machine use/ storage at temperatures below 0 C/32 F. In these cases, the warranty will be invalidated. 1.1 To simplify Manual Reading The warning triangle indicates the instructions that are important for the user s safety. Please carefully follow these instructions to avoid serious injury! Fig.1 References to illustrations, parts of the appliance and controls are indicated by numbers or letters. Whenever possible, refer to the illustration. This symbol is used to highlight information that is particularly important to ensure optimal use of the machine. 1.2 How to use these Operating Instructions Keep these operating instructions in a safe place and make them available to anyone who may use the coffee machine. For further information or if you experience problems not please contact Customer Service at Saeco USA (1-800-933-7876) or Saeco Canada (1-514-385-5551). 2 TECHNICAL SPECIFICATIONS Nominal voltage Power rating Power supply See label on the appliance Housing Metal and Thermoplastic material Size (w x h x d) 235 x 350 x 270 mm / 9.25 x 13.78 x 10.63 in Weight 5.3 kg / 11.68 lbs Cord length 1.2 m / 47.24 in Control panel Front Water tank 2 liters / 67.6 oz (removable) Pump pressure 15 bar Boiler Stainless steel type Safety devices Boiler pressure safety valve - Safety thermal fuse Subject to engineering and manufacturing changes due to technological improvements. 18

Key to Machine Components: Cup-warming plate illy button illy light Power button English Brew button Machine ready light Steam button Hot water / steam knob Brew unit Water tank Cappuccinatore Drip tray + grill ESE pod A Pannarello frother 25 cm 10 in Ground coffee measuring scoop 10 cm 4in 10 cm 4in 30 cm 12in Ground coffee 10 cm 4in 19

3 SAFETY REGULATIONS Do not put live parts in contact with water: Danger of short circuit! Overheated steam and hot water may cause scalding! Do not direct the steam or hot water jet towards body parts. Handle the steam/hot water spout with care: Danger of scalding! Intended Use of the Machine The coffee machine is intended for domestic use only. Do not make any technical changes or use the machine for unlawful purposes since this would create serious hazards! The appliance is not for use by persons (included children) with reduced physical, mental or sensory abilities or with scarce experience and/or competences, unless they are supervised by a person responsible for their safety or they are instructed by him/her to use the machine. Prevent children from playing with the machine. Power Supply Only connect the coffee machine to a suitable socket. The voltage must correspond to the indication on machine s label. Power Cord Never use the coffee machine if the power cord is defective. If damaged, the power cord must be replaced by the manufacturer or its authorised service center. Do not pass the cable around corners, over sharp edges or over hot objects and keep it away from oil sources. Do not use the power cord to carry or pull the coffee machine. Do not pull out the plug by the power cord or touch it with wet hands. Do not let the power cord hang freely from tables or shelves. Personal Safety Guidelines Make sure children cannot play with the coffee machine. Children do not realize the dangers associated with household appliances. Do not leave the coffee machine packaging within the reach of children. Danger of Burns Never direct jets of hot steam and/or hot water towards yourself or others. Always use the handles or knobs provided. Hot water drips may spill out of the coffee brew unit during the warming phase. Machine Location Place the coffee machine in a safe place, where no danger of overturning or injury can be caused. Hot water or overheated steam may spill out of the machine: Danger of scalding! Do not keep the machine at a temperature below 0 C/32 F; frost may damage the machine. Do not use the coffee machine outdoors. Do not place the machine on hot surfaces and close being damaged. Cleaning the Machine Before cleaning the machine, you must deselect all buttons and remove the plug from the socket. Wait for the machine to cool down. Do not immerse the machine in water! It is strictly forbidden to tamper with the internal parts of the machine. Suitable Location for Operation and Maintenance To ensure machine best performance, we reccomend to check the following: Choose a level surface; and near an easily reachable socket; Provide for a minimum distance from the sides of the Storing the Machine In case of inactivity of the machine for a certain period of time, switch it off and unplug it from the socket. Store it in a dry place and out of reach of children. Shelter it from dust and dirt. Servicing / Maintenance In case of failure, problems or a fault resulting from a suspected fall of the machine, you should immediately remove the plug from the socket. Never attempt to operate a faulty machine. Servicing and repairs may only be carried out by authorized service centers. All liability for damage resulting from work not carried 20

out by professionals is declined. Fire Safety Precautions 2 ) extinguishers. Do not use water or dry powder extinguishers. 4 MACHINE INSTALLATION For your safety and that of others, strictly follow the Safety regulations detailed in section 3. 4.1 Packaging of Machine The original packaging has been designed to protect the machine during transportation. We recommend keeping the packaging carton for possible future transportation. 4.4 Filling the Water Tank (Fig.1) - Remove the water tank. An automatic device lifts the water suction pipe. (Fig.2) (Fig.3) - Reinsert the tank into its housing. Press immerses the suction pipe in water. Fill the tank with only fresh, non-sparkling, drinking water. Hot water or any other liquid may damage the tank. Do not switch on the machine with empty tank: Make sure there is enough water in the tank. 4.5 Priming the Water Circuit English 4.2 Installation Instructions Before installing the machine, observe the following safety precautions: Place the machine in a safe place; Make sure children cannot play with the machine; Avoid placing the machine on very hot surfaces or The coffee machine is now ready to be connected to the power supply. 4.3 Power Supply Connection Electric power may be very dangerous! It is therefore necessary that the safety regulations be carefully respected. Do not use faulty power cords! Faulty cords and plugs must be replaced immediately in authorized customer service centers. The voltage of the appliance has been pre-set by the manufacturer. Check that the voltage matches the references on the label, at the bottom of the appliance. Check that the power button is set on 0 before connecting the machine to the power supply. Only connect the plug to a socket with suitable voltage. Before starting up the machine, after a long period of inactivity, and whenever the tank is empty, the machine s water circuit must be primed. (Fig.4) - Switch on the machine by means of the power button - I position. (Fig.5) - Place a container under the cappuccinatore. Open the hot water/steam knob by turning the knob counter-clockwise. (Fig.6) - Press the brew button. cappuccinatore. Press the brew button again. (Fig.7) - Close the hot water/steam knob by turning it clockwise. Remove the container. The machine is now ready to brew coffee and dispense steam. Please see related sections for operating details. (Fig.48) - Cups can be warmed on the cupwarming surface. When the machine is on, the cup-warming surface is always on. Please be very careful when you are around this area: Danger of slight burns. 21

5 COFFEE BREWING Warning! During coffee brewing, do not remove Danger of burns. This should be considered a standard operation. Before use, make sure the hot water/steam knob If the machine is off, switch it on by means of the power button. During the warming phase, the machine ready light (Fig. 8). The machine is now ready for coffee brewing. Warning! By pressing the brew button during the brew unit: Danger of burns. 5.1 Using illy Coffee Pods The machine has been designed and manufactured to get the best performance with "illy" pods. (Fig.9) (Fig.11) unit from the bottom. (Fig.12) locks into place. (Fig.21) brewed). the brew button again to stop dispensing water. (Fig.14) - Press the illy button. The light turns on and the machine warms up to the right temperature. (Fig.10) make sure the paper of the pod does not stick out of Check that the temperature ready light is permanently on. (Fig.11) the bottom. (Fig.12) locks into place. (Fig.13) - Take 1 preheatedcup and place it under the coffee brewing spout. (Fig.15) - Press the coffee brew button. When the desired quantity of coffee has been reached, press the coffee brew button again to stop brewing, and remove the cup of coffee. Wait a few seconds after brewing, then remove the section 9). 5.2 Using Ground Coffee For brewing pre-ground coffee, only use the ground (Fig.16) (Fig.18) the bottom. (Fig.19) locks into place. automatically slightly turned towards the left. This optimal functionality. (Fig.21) brewed). the brew button again to stop dispensing water. (Fig.22) by turning it from right to left, and drain any water (Fig.17) -With the measuring scoop provided, add 1 two coffees, respectively. Clean any coffee residues (Fig.18) the bottom. (Fig.19) locks into place. (Fig.20) - Take 1or2preheatedcups and place them placed under the coffee dispensing spouts. (Fig.21) - Press the coffee brew button. 22

When the desired quantity of coffee has been reached, press the coffee brew button again to stop brewing, and remove the cups of coffee. (Fig.22) - Wait a few seconds after brewing, then grounds. Note for cleaning: Always remove the ground both parts thoroughly under running water (see section 9). BEFORE PERFORMING ANY OPERATIONS RELATED TO STEAM DISPENSING OR HOT WATER DISPENSING, CHECK THAT THE STEAM SPOUT (PANNARELLO OR CAPPUCCINATORE) IS DIRECTED OVER THE DRIP TRAY. 6 PREPARING CAPPUCCINO Danger of burns! Brewing may be preceded by small jets of hot water. The spout can reach high temperatures: Never touch it with bare hands. (Fig.4) - If the machine is off, switch it on by means of the power button. permanently on. (Fig.23) - Press the steam button. The machine will enter another warm-up phase. During the warming phase, the machine ready light is now ready to dispense steam. Warning: Never use steam when the cappuccinatore or the Pannarello have been removed. Danger of burns! (Fig.24) - Direct the cappuccinatore towards the drip tray; open the hot water/steam knob for a few seconds to drain any residual water left in the cappuccinatore. Afterwards, only steam will come out of the spout. Close the hot water/steam knob. the suction tube. In this case, direct the tube towards the drip tray. (Fig.25) - Insert the suction tube into a container of milk. (Fig.26) - Place a cup below the cappuccinatore, ensuring that it is on a stable surface. Open the hot water/steam knob and dispense milk into the cup. (Fig.27) - Set the desired froth level by adjusting the peg; higher position = thicker froth. To clean the knob, insert the suction tube into a water container and start dispensing steam. Drain the water into a container until only (Fig.28) - Press the steam button again. that the temperature is too high. Prime the circuit as described in section 4.5 to make the machine ready for use. Note: The machine is ready when the machine ready light is permanently on. Note: If it is not possible to make a cappuccino or to clean the cappuccinatore as described, prime the circuit as explained in section 4.5. Then repeat the operations. 7 HOT WATER DISPENSING Danger of burns! Brewing may be preceded by short sprays of hot water. The brewing spout may reach high temperatures: Never touch it with bare hands. (Fig.4) - If the machine is off, switch it on by means of the power button. permanently on. (Fig.29) - Remove the cappuccinatore by pulling it outwards. Warning: Never dispense hot water with the cappuccinatore or Pannarello removed. Danger of burns! (Fig.30-31) - Insert the Pannarello completely onto the steam arm, and turn it 90 counter-clockwise. (Fig.32) - Place a container under the steam spout (Pannarello). Open the hot water/steam knob by turning it counterclockwise. (Fig.33) - Press the coffee brew button to dispense water until the desired quantity is reached. When the desired quantity of hot water has been English 23

dispensed, press the coffee brew button again. (Fig.35) - To close the knob, turn it clockwise. Remove the hot water container. 8 STEAM DISPENSING Danger of burns! Steaming may be preceded by short jets of hot water. The spout can reach high temperatures: Never touch it with bare hands. Steam may be used to warm up any beverage. For steam dispensing, use the Pannarello (see section 7 for installation). (Fig.4) - If the machine is off, switch it on by means of the power button. permanently on. (Fig.34) - Press the steam button. The machine will enter another warm-up phase. During the warming phase, the machine ready light is now ready to dispense steam. (Fig.32) - Insert a container below the steam spout and open the hot water/steam knob for a few seconds, so that the residual water comes out of the spout. Afterwards, only steam will come out. (Fig.35) - Close the knob and remove the container. (Fig.36) - Immerse the steam spout in the beverage to be warmed up and open the knob. Turn the container with slow upward movements so that the beverage is warmed up evenly. After dispensing steam for the desired time, close the knob. Remove the container with the heated beverage. (Fig.37) - Press the steam button again. that the temperature is too high. Prime the circuit as described in section 4.5 to make the machine ready for use. After this operation, thoroughly clean the steam spout with a wet cloth. 9 CLEANING THE MACHINE Maintenance and cleaning can only be carried out when the machine is cold and disconnected from the power supply. Do not immerse the machine in water or place any of its parts in a dishwasher. Do not use sharp objects or harsh chemical products (solvents) for cleaning. (Fig.38) - We recommend cleaning the water tank (Fig.39) - Empty and clean the drip tray daily. Use a soft, dampened cloth to clean the appliance. (Fig.40-41-42-43) follows: and wash them thoroughly; with water. After frothing milk, always be sure to dispense a small quantity of hot water to clean the inside of the steam spout. Use a soft, dampened cloth to clean the outside of the appliance. After frothing milk, clean the cappuccinatore as described in section 6. For a thorough cleaning of the cappuccinatore, proceed as follows: - (Fig.29 and Fig.44) - Remove the cappuccinatore from the machine and separate its components manually; - (Fig.45-46) - Wash the components with running water; - Wash the suction tube with running water; - (Fig.47) - When this procedure is completed, assemble the cappuccinatore and insert it into the machine. Do not dry the machine and/or its components using a microwave and/or conventional oven. 10 DESCALING THE MACHINE Limescale normally builds up with the use of the appliance. Descaling is necessary every 3-4 working months and/or If you want to descale the machine yourself, you can use a non-toxic and/or non-harmful descaling product for coffee machines, commonly available in retail stores. We recommend using Saeco descaling solution. Warning! Do not use vinegar as a descaler. Make sure the Pannarello is inserted, and the machine is turned off. (see section 7). (Fig.1) - Remove the water tank and drain the remaining water. 24

(Fig.2-3) - Mix the descaling solution with water as (Fig.4) - Switch on the machine by pressing the power button. (Fig.32) - Place a container below the steam spout. (Fig.32-33) - At intervals, dispense one cup of water at a time, by turning the steam knob counter-clockwise and pressing the brew button. To stop dispensing, press the brew button again and turn the steam knob clockwise. (Fig.4) - During each interval allow the descaling solution to sit for about 10-15 minutes, switching off the machine by means of the power button. Empty the container. (Fig.2) drinking water. content by turning the steam knob counter-clockwise and pressing the brew button. To stop dispensing, press the brew button again and turn the steam knob clockwise. Let the machine warm up, and empty the water tank as described above. product. For more detailed information about recycling household waste disposal service or the shop where you purchased the product. English If you are using a descaling product other than the one recommended, it is important that you carefully follow the manufacturer s instructions detailed on the package of the descaling product. 11 MACHINE DISPOSAL Put unused appliances out of service. Disconnect the plug from the socket and cut the electrical cord. At the end of its life, take the appliance to a suitable waste collection site. This product complies with EU Directive 2002/96/EC. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this 25

Problem Possible cause Solution The machine does not switch on. The machine is not connected to the power supply. Connect the machine to the power supply. The pump is very noisy. The water tank is empty. The temperature ready light was pressed. The coffee is too cold. (section 5). The cups are cold. Preheat the cups on the cup-warming surface. The milk does not froth. The milk is not suitable: Powdered Use only cold, whole milk. milk or low-fat milk has been used. Prime the circuit (section 4.5) and repeat the There is no steam left in the boiler. It is not possible to make a operations described in section 6. cappuccino. Clean the cappuccinatore as described in The cappuccinatore is dirty. section 9. Coffee does not brew. Prime the circuit as described in section 4.5. The machine is over temperature, the When the machine ready light is permanently on, coffee may be brewed. There is too little coffee in the Add coffee (section 5). The coffee is brewed too The grind is too coarse. Use a different blend. fast, crema does not form. The pod is too old. Replace the old pod with a new one. The illy button has not been Press the illy button and wait until the machine pressed. Water tank is empty. There is too much coffee in the Reduce the quantity of coffee in the Coffee is not brewed or brewed in drips only. The hot water/steam knob is open. Close the knob. The machine has limescale buildup. Descale the machine (section 10). The filter in the portafilter is clogged. The pod is not suitable. Change type of pod. in the brew unit. edges. dirty. The gasket of the boiler is dirty. The pod is inserted incorrectly. Clean the gasket. Insert the pod correctly. Please contact an authorized service center for any problems not covered in the above table or when the suggested solutions do not solve the problem. Saeco USA Customer Service 1-800-933-7876. 26

EC DECLARATION OF CONFORMITY EC 2006/95, EC 2004/118, EC 1992/31, EC 1993/68 We : Saeco International Group Via Torretta, 240 40041 GAGGIO MONTANO (BO) English declare under our responsibility that the product : COFFEE MAKER TYpe : SIN 17XNI to which this declaration relates is in conformity with the following standards or other normative documents : Safety of household and electrical appliances - General requirements EN 60335-1(2002 ) + A1(2004) + A2(2006) + A11(2004) + A12(2006) Safety of household and electrical appliances - Part 2-15 Particular requirements for appliances for heating liquids EN 60335-2-15(2002) + A1(2005) EN 50366 (2003) + A1 (2006). Electromagnetic compatibility (EMC) - Requirements for household appliances, electric tools and similar apparatus - Part 1 Emission EN 55014-1 (2000) + A1 (2001) + A2 (2002). Electromagnetic compatibility (EMC) EN 61000-3-2 (2000) Electromagnetic compatibility (EMC) EN 61000-3-3 (1995) + A1 (2001) Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 2. Immunity - Product family standard EN 55014-2 (1997) + A1 (2001) following the provisions of the Directives : EC 73/23, EC 89/336, EC 92/31, EC 93/68. Gaggio Montano 05/07/2007 R&D Ing. Andrea Castellani 27

50

51

COD. 15001266 REV. 00 DEL 20-08-07 Type Sin017XNI Saeco International Group S.p.A. Via Torretta, 240-40041 Gaggio Montano Bologna - Italy Tel. +39 0534.771.111 - Fax. +39 0534.31025 http://www.saeco.com