Z Close supervision is necessary when any appliance is used by or near children.

Transcription

1 Instructions for Use The NA 3 Instructions for Use has be awarded the seal of approval by the indepdt German Technical Inspection Agcy, TÜV SÜD, due to s easy-to-understand style, s thoroughness and coverage of safety aspects.

2 NA 3 IMPORTANT SAFGUARDS These safeguards apply for machines wh UL safety test (see rating plate and chapter 8, Technical data ). Follow the basic safety precautions Wh using electrical appliances, basic safety precautions should always be followed, to reduce the risk of fire, electric shock, and/or injury to persons, including the following: Z Read all instructions. Z Do not touch hot surfaces. Use handles or knobs. Z To protect against fire, electric shock and injury to persons, do not immerse cord, plugs, or body of machine in water or other liquid. Z Close supervision is necessary wh any appliance is used by or near childr. Z Unplug from outlet wh not in use and before cleaning. Allow to cool before putting or taking off parts, and before cleaning the appliance. Z Do not operate any appliance wh a damaged cord or plug or after the appliance malfunctions, or has be damaged in any manner. Return appliance to the nearest authorized service facily for examination, repair or adjustmt. Z The use of accessory attachemt not recommded by the appliance manufacturer may result in fire, electric shock, or injury to persons. Z Do not use outdoors. Z Do not let the cord hang over the edge of a table or counter, or touch hot surfaces. Z Do not place on or near a hot gas or electric burner, or in a heated ov. Z Always attach plug to appliance first, th plug cord into the wall outlet. To disconnect, turn any control to OFF th remove plug from wall outlet. Z Do not use appliance for other than intted use. Z Use extreme caution wh dispsing hot steam. Z For household use only. SAV THS INSTRUCTIONS 2

3 NA 3 Special cord set instructions a. A short power supply cord is provided to reduce the risk resulting from becoming tangled in or tripping over a long cord. Your NA has a 3-pin grounded plug. b. Longer extsion cords are available and may be used if care is exercised in their use. c. If an extsion cord is used, 1. the marked electrical rating of the extsion cord should be at least as great as the electrical rating of the appliance, and 2. if the appliance is of the grounded type, the extsion courd should be a grounding type 3-wire cord, and 3. the longer cord shall be arranged so that will not drape over the counter top or tabletop where can be pulled on by childr of tripped over. Z Z Z As a safety feature, this plug will f in a polarized outlet only one way. If the plug does not f fully in the outlet, reverse the plug. If still does not f, contact a qualified electrician. Do not modify the plug in any way or attempt to defeat this safety feature. Warning Caution To reduce the risk of fire or electric shock, do not remove any service covers. No user serviceable parts inside. Repair should be done by authorized personnel only. This appliance is for household use. Any servicing other than cleaning and user rinse should be performed by an authorized service represtative: Z Do not immerse base in water or try to disassemble. Z To reduce the risk of fire or electric shock, do not remove the base. No user serviceable parts inside. Repair should be done by authorized service personnel only. Z Check voltage to be sure that the voltage indicated on the name plate agreees wh your voltage. Z Never use warm or hot water to fill the water container! Use cold water only. Z Keep your hands and the cord away from hot parts of the appliance during operation. Z Never clean wh scouring powders or hard implemts. 3

4 NA 3 NVR DO (or you will void your warranty protection): Z Z Z Z Never fill instant coffee, chocolate mix etc. into the grinder or ground coffee funnel (grinder by-pass). It will damage the functioning of the brewing chamber. Never fill sugar coated coffee beans into the bean hopper. In case of doubt, call your dealer. Never fill anything other than coffee beans into the bean container (no chocolate, no rice, no nuts, no spices, nothing other than roasted coffee beans). Never do anything wh the machine which is not described in the User s Manual. In case of doubt, call your dealer. 4

5 NA 3 5

6 NA 3 Your NA 3 IMPORTANT SAFGUARDS 2 Control elemts 8 Proper use 10 For your safety 10 Welcome to the world of JURA 11 Knowledge Builder...11 Connector System colour plain text display Preparing and using for the first time 12 Setting up...12 Filling the water tank...12 Filling the bean container...12 First-time use...12 Using and activating filter Determining and adjusting the water hardness...14 Adjusting grinder...14 Swching on the machine...15 Swching off the machine Preparation 15 1 coffee at the touch of a button coffees at the touch of a button...16 Pre-ground coffee...16 One-off setting before and during preparation...16 ntering a default setting for the amount of water for a cup size...17 Cappuccino wh the Professional Cappuccino Frother...17 Cappuccino wh the asy Cappuccino Frother...18 Cappuccino wh the 2-stage frothing nozzle...18 Heating milk wh the Professional Cappuccino Frother...19 Heating milk wh the 2-stage frothing nozzle...19 Hot water Default settings in programming mode 20 Products...20 nergy-saving mode...21 Automatic swch-off...21 Uns of water...21 Language Rinse 22 Rinse tips Rinsing the machine manually Changing the filter following a prompt Changing the filter manually Cleaning the machine following a prompt Cleaning the machine manually...24 Descaling the machine following a prompt...24 Descaling the machine manually...25 Rinsing the Professional Cappuccino Frother

7 NA 3 Cleaning the Professional Cappuccino Frother...26 Dismantling and rinsing the Professional Cappuccino Frother Rinsing the asy Cappuccino Frother Cleaning the asy Cappuccino Frother Dismantling and rinsing the asy Cappuccino Frother...28 Dismantling and rinsing the 2-stage frothing nozzle...28 Cleaning the bean container...29 Descaling the water tank Display messages 30 6 Troubleshooting 31 7 Transport and vironmtally neutral disposal 32 Transport/mptying the system Disposal Technical data 32 9 Contacts 32 Index 33 Symbol description Warnings: J CAUTION Always take note of any information marked wh the words CAUTION or WARNING and a warning sign. The signal word WARNING points out pottial risk of serious injury, and the signal word CAUTION pottial risk of slight injury. CAUTION The CAUTION symbol is used to draw atttion to circumstances which could result in damage to the machine. Symbols used: Information and tips to make use of your NA ev easier. Prompt to take action. This symbol means that you are being prompted to perform an action. Referces to the JURA webse where you can find interesting addional information: 7

8 NA 3 Control elemts Figure: NA 3 Blossom Whe 1 Water tank 2 Powder chaft for pre-ground coffee 3 Coffee grounds container 4 Drip tray 5 Cup platform 6 Bean container cover 7 l Swch for hot water and steam preparation 8 Connector System for removable nozzles 9 2-stage frothing nozzle 10 Height-adjustable coffee spout 8

9 NA Figure: Op cover Q On/off button 2 Grinding wheel 3 Cover 4 P P button 5 c Rinse button 6 g Rotary Swch 7 Display 8 Professional Cappuccino Frother 9 asy Cappuccino Frother 10 2-stage frothing nozzle 11 Hot water nozzle The following nozzles are available from stockists and can be fted to the Connector System :

10 NA 3 Proper use The machine has be designed and built for domestic use. It should only be used to prepare coffee and to heat milk and water. Use for any other purpose will be deemed improper. JURA lektroapparate AG cannot accept any responsibily for the consequces of improper use. Before using the machine always carefully read and comply wh all these instructions. Keep this manual close to the NA and pass on to the next user if applicable. For your safety Please read and note the following important safety information carefully. This can prevt pottially fatal injury due to electric shock: Z Never use a machine which has be damaged or which has a defective power cable. Z If there are any signs of damage, for example if there is a smell of burning, unplug the machine from the mains supply immediately and contact the JURA service ctre. Z If the power cable for this machine is damaged, must be repaired eher directly by JURA or by a JURA approved service ctre. Z Make sure that the NA and the power cable are not located close to hot surfaces. Z Be careful to sure that the power cable does not become trapped and does not rub against sharp edges. Z Never op and repair the machine yourself. Do not modify the machine in any way that is not described in the NA manual. The machine contains live parts. If oped, there is a danger of fatal injury. Repairs may only be carried out by JURA approved service ctres, using original spare parts and accessories. There is a risk of scalds and burns from the spouts or the nozzle: Z Place the machine out of the reach of childr. Z Do not touch any hot parts. Use the handles provided. Z Be careful to sure that the appropriate nozzle is correctly installed and clean. The nozzle or parts of the nozzle could become detached if the parts are not assembled correctly or a blockage occurs. A defective machine is not safe and could cause injury or fire. To avoid damage and any associated risk of injury or fire: Z Never allow the power cable to hang down loosely. The power cable can trip someone or be damaged. Z Protect your NA from vironmtal influces such as rain, frost and direct sunlight. Z Do not put the NA, cable or connections in water. Z Do not put the NA or any individual parts in the dishwasher. Z Turn your NA off and disconnect the mains plug before starting any cleaning operation. Always wipe your NA wh a damp cloth, never a wet cloth, and protect from constant water splashes. Z Only connect the machine to a power supply in accordance wh the information on the rating plate. The rating plate is located on the underside of your NA. Further technical data is giv in Chapter 8 Technical Data. Z Use only original JURA care products. Use of accessories that are not explicly recommded by JURA could damage the NA. Z Do not use any coffee beans treated wh addives or caramelised coffee beans. Z Always fill the water tank wh cold, fresh water. Z If you are abst for a prolonged period of time, turn the machine off. 10

11 NA 3 Risk to childr and persons wh limed capabilies in operating machines: Z The machine is not designed to be operated by childr and persons wh limed capabilies. Z The machine may only be used by persons who are able to operate the machine safely. Connector System The Connector System perms the use of four differt nozzles: Z Professional Cappuccino Frother U Cappuccino U Hot milk Safe handling of the CLARIS filter cartridges: Z Filter cartridges should be kept out of the reach of childr. Z Store filter cartridges dry in the sealed package. Z Protect filter cartridges from heat and direct sunlight. Z Do NOT use damaged filter cartridges. Z Do NOT op filter cartridges. Z asy Cappuccino Frother U Cappuccino Welcome to the world of JURA JURA on the Internet Vis us on the At you will find the latest interesting information about your NA and all facets of the world of coffee. Knowledge Builder You can also get to know your NA in a fun way on the PC. Z 2-stage frothing nozzle U Cappuccino U Hot The Knowledge Builder awas you at LO, the interactive assistant, will assist you and explain the befs of NA and how is used. 11

12 NA 3 Z Hot water nozzle T Remove the water tank and rinse wh cold water. T Fill the water tank wh cold, fresh water and replace the tank. Filling the bean container 3-colour plain text display Your NA features a 3-colour plain text display. The colours of the display texts have the following meanings: Z Gre: Your NA is ready for use. Z Red: The NA is prompting you to perform an action. Z Yellow: You are in programming mode. 1 Preparing and using for the first time This chapter provides the information you need for trouble-free use of your NA and gives you a step-by-step guide to preparing your NA for your first coffee experice. Setting up Wh setting up your NA, please note the following: Z Place the machine on a horizontal surface that cannot be damaged by water. Z Select a posion for the NA where is protected against overheating. Filling the water tank To joy perfect coffee we recommd changing the water every day. CAUTION Milk, mineral water or other liquids can damage the water tank or the machine. T Only fill the water tank wh fresh, cold water. CAUTION Coffee beans which have be treated wh addives (e.g. sugar), pre-ground or freeze-dried coffee will damage the grinder. T Only use untreated coffee beans to refill the bean container. T Remove the bean container cover. T Remove any dirt or foreign objects from the bean container. T Fill the bean container wh coffee beans. T Close the bean container. First-time use The on/off button also acts as a power swch. Wh the NA is swched off, the machine is completely disconnected from the power supply. J WARNING If the machine is operated wh a defective power cable, there is a danger of electric shock. T Never use a machine which has a defective power cable. Precondion: The water tank must be full. T Insert the mains plug into a power socket. Q T Press the on/off button to swch the machine on. SPRACH DUTSCH 12

13 NA 3 g T Turn the Rotary Swch until LANGUAG NGLISH is Using and activating filter Your NA no longer requires descaling if you use CLARIS filter cartridges. Perform the Insert filter operation whout interruptions. This will sure optimum function of your NA. After two months the filter capacy is reached. The elapsed time can be checked wh the date plate on the cartridge holder. k T Press the Rotary Swch to confirm the language setting. OK, the language is th adjusted. OPN TAP T Place a receptacle under the nozzle. SYSTM FILLING CLOS TAP y T Turn the swch to posion o. HATING PRSS ROTARY T Place a receptacle under the coffee spout. k T Press the Rotary Swch to start rinsing. RINSING RADY Precondion: RADY is shown on the display. T Op the cover behind the Rotary Swch. P T Press the P button until RINS appears. g T Turn the Rotary Swch until FILTR - is k T Press the Rotary Swch to ter the programme em. NO - g T Turn the Rotary Swch until YS p appears. k T Press the Rotary Swch to confirm the setting. OK INSRT FILTR T Remove and empty the water tank. T Op the cartridge holder. T Insert the new filter cartridge into the water tank, pressing slightly. Wh a coffee specialy has be prepared for the first time, is possible that FILL BANS appears on the display as the grinder has not yet be completely filled wh coffee beans. In this case prepare a differt coffee specialy. T Close the cartridge holder. It will click into place audibly. T Fill the water tank wh cold, fresh water and replace the tank. T Place a receptacle (at least 500 ml) under the nozzle. 13

14 NA 3 OPN TAP FILTR RINSING, water is discharged from the nozzle. Rinsing of the filter can be interrupted at any time. To this purpose turn the swch clockwise. The water may be slightly discoloured. This is not harmful to health and does not affect the taste. Rinsing of the filter stops automatically, CLOS TAP. y T Turn the swch to posion o. HATING RADY The filter is now activated. Determining and adjusting the water hardness The harder the water, the more frequtly the NA requires descaling. It is therefore important to adjust the water hardness. It is not possible to adjust the water hardness if the CLARIS filter cartridge is used and activated. The water hardness can be adjusted betwe 1 dh and 30 dh. It can also be deactivated, which means that the NA will not indicate wh has to be descaled. The Aquadur test strip supplied as standard can be used to determine the water hardness. T Hold the test strip briefly (for one second) under running water. T Shake off the water. T Wa for approximately 1 minute. T Read the degree of water hardness from the discolouration of the Aquadur test strip and the description on the packaging. The water hardness can th be adjusted. xample: Changing the water hardness from 16 dh to 25 dh. Precondion: RADY is shown on the display. T Op the cover behind the Rotary Swch. P T Press the P button until RINS appears. g T Turn the Rotary Swch until HARDNSS is k T Press the Rotary Swch to ter the programme em. 16 dh g T Turn the Rotary Swch until 25 dh is k T Press the Rotary Swch to confirm the setting. OK, the water hardness is th adjusted. HARDNSS g T Turn the Rotary Swch until XIT is k T Press the Rotary Swch to ex programming mode. RADY Adjusting grinder You can adjust the grinder continuously to su the roast of your coffee. CAUTION If you adjust the finess of grind wh the grinder is not operating, the grinding wheel could be damaged. T Only adjust the finess of grind wh the grinder is running. The finess of grind setting is correct if the coffee flows regularly from the coffee spout. A fine, thick crema is also formed. Our recommdations: Z Select a fine setting for a light roast. 14

15 NA 3 U If the finess of grind setting is too fine, the coffee only drips from the coffee spout. Swching on the machine Wh the NA is swched on, a prompt to perform a rinse operation automatically appears. Z Select a coarse setting for a darker roast. U If the finess of grind is too coarse the coffee flows too quickly from the coffee spout. Q T Press the on/off button to swch the NA on. HATING PRSS ROTARY T Place a receptacle under the coffee spout. k T Press the Rotary Swch to start rinsing. RINSING, the system is being rinsed, the operation stops automatically. RADY Swching off the machine Wh the NA is swched off, the system is automatically rinsed if a coffee specialy has be prepared. xample: Adjusting the finess of grind during coffee preparation. T Place the cup under the coffee spout. k T Press the Rotary Swch to start coffee preparation. T Turn the finess of the grinding wheel to the desired posion while the grinder is running. 1 CUP, the pre-set amount of water flows into the cup, preparation stops automatically. RADY T Place a receptacle under the coffee spout. Q T Press the on/off button. RINSING, the system is being rinsed. The operation stops automatically, the NA is swched off. The on/off button also acts as a power swch. Wh the NA is swched off, the machine is completely disconnected from the power supply. 2 Preparation 1 coffee at the touch of a button Precondion: RADY is shown on the display. T Place the cup under the coffee spout. k T Press the Rotary Swch to start coffee preparation. During grinding the strgth of the coffee is briefly 1 CUP, the pre-set amount of water flows into the cup, preparation stops automatically. RADY 15

16 NA 3 2 coffees at the touch of a button Precondion: RADY is shown on the display. T Place two cups under the coffee spout. g T Turn the Rotary Swch until 2 CUPS is k T Press the Rotary Swch to start coffee preparation. 2 CUPS, the pre-set amount of water flows into the cups, preparation stops automatically. RADY Pre-ground coffee You can also use a second coffee bld in the powder chaft for pre-ground coffee. Never add more than two level measuring spoons of pre-ground coffee. Do not use very finely-ground coffee. Very fine coffee can block up the system so that the coffee only comes out in drips. If the filled amount of pre-ground coffee was insuffic, NOT NOUGH PR- GROUND is displayed and the NA stops operation. The desired coffee specialy must be prepared whin approx. one minute after filling wh the pre-ground coffee. Otherwise the NA stops the operation and is ready to use again. xample: Preparing a cup of coffee using pre-ground coffee. Precondion: RADY is shown on the display. T Place the cup under the coffee spout. T Op the powder chaft. FILL PR-GROUND T Place the filler funnel for pre-ground coffee in the powder chaft. T Place one level measuring spoon of pre-ground coffee into the filler funnel. T Remove the filler funnel. T Close the powder chaft. 1 CUP k T Press the Rotary Swch to start coffee preparation. 1 CUP, the pre-set amount of water flows into the cup, preparation stops automatically. RADY It is also possible to prepare two cups of pre-ground coffee. To this purpose place two level measuring spoons of pre-ground coffee into the filler funnel. Turn the Rotary Swch to 2 CUPS and press to start coffee preparation. One-off setting before and during preparation The coffee strgth can be changed before preparation or during the grinding operation. The following coffee strgth options are possible for 1 coffee: Z Mild Z Normal Z Strong 2 coffees are always prepared wh the coffee strgth mild. 16

17 The pre-set amount of water can be changed during the brewing operation by turning the Rotary Swch. One-off settings before and during coffee preparation always follow this model. These settings are not saved. xample: Changing the coffee strgth of 1 coffee before preparation from NORMAL to STRONG. Precondion: RADY is shown on the display. T Place the cup under the coffee spout. g T Turn the Rotary Swch until STRONG is k T Press the Rotary Swch until STRONG is During grinding the coffee strgth STRONG is 1 CUP, the pre-set amount of water flows into the cup, preparation stops automatically. RADY NA 3 k T Press the Rotary Swch again wh ough coffee has be filled into the cup. OK, the default setting for the amount of water for one coffee has be tered. RADY This setting can be changed at any time by repeating the above procedure. Cappuccino wh the Professional Cappuccino Frother Precondion: RADY is shown on the display. T Remove the protective cover from the Professional Cappuccino Frother. T Connect the milk pipe to the nozzle. T Insert the other d of the milk pipe into a milk carton or connect to a milk container. T Place a cup under the nozzle. T Set the selector lever of the nozzle to the milk foam p posion. ntering a default setting for the amount of water for a cup size A default setting can be tered for the amount of water for 1 coffee. Wh preparing 2 coffees this amount is dispsed per cup. Precondion: RADY is shown on the display. T Place the cup under the coffee spout. k T Press the Rotary Swch and hold down. During grinding the strgth of the coffee is k T Continue to hold the Rotary Swch down until NOUGH COFF? appears. The coffee flows into the cup. g T Turn the Rotary Swch until STAM is HATING RADY appears as soon as the NA is sufficly heated. STAM, the milk foam is being prepared. y T Turn the swch clockwise to posion o wh there is suffic milk foam in the cup. You can prepare more milk foam whin about 40 seconds. 17

18 NA 3 T Place the cup under the coffee spout. k T Press the Rotary Swch to start coffee preparation. 1 CUP, the pre-set amount of water flows into the cup. Preparation stops automatically. To sure that the Professional Cappuccino Frother works perfectly, should be rinsed and cleaned regularly (refer to Chapter 4 Rinse Professional Cappuccino Frother ). Cappuccino wh the asy Cappuccino Frother Precondion: RADY is shown on the display. T Remove the protective cover from the asy Cappuccino Frother. T Connect the milk pipe to the nozzle. T Insert the other d of the milk pipe into a milk carton or connect to a milk container. T Place a cup under the nozzle. You can prepare more milk foam whin about 40 seconds. T Place the cup under the coffee spout. k T Press the Rotary Swch to start the coffee preparation. 1 CUP, the pre-set amount of water flows into the cup. Preparation stops automatically. To sure that the asy Cappuccino Frother works perfectly, should be rinsed and cleaned regularly (refer to Chapter 4 Rinse asy Cappuccino Frother ). Cappuccino wh the 2-stage frothing nozzle Precondion: RADY is shown on the display. T Push the 2-stage frothing nozzle to the lower posion. T Place a cup of milk below the 2-stage frothing nozzle and immerse the nozzle in the milk. g T Turn the Rotary Swch until STAM is HATING RADY appears as soon as the NA is sufficly heated. STAM, the milk foam is being prepared. y T Turn the swch clockwise to posion o wh there is suffic milk foam in the cup. If the nozzle does not reach into the cup, lift the cup towards the nozzle. g T Turn the Rotary Swch until STAM is HATING RADY appears as soon as the NA is sufficly heated. STAM, the milk is foamed by the hot steam. 18

19 y T Turn the swch to posion o wh the milk foam has reached the required consistcy. You can prepare more steam whin about 40 seconds. T Place the cup under the coffee spout. k T Press the Rotary Swch to start coffee preparation. 1 CUP, the pre-set amount of water flows into the cup. Preparation stops automatically. To sure that the 2-stage frothing nozzle works perfectly, should be rinsed regularly (refer to Chapter 4 Rinse Dismantling and rinsing the 2-stage frothing nozzle ). Heating milk wh the Professional Cappuccino Frother Precondion: RADY is shown on the display. T Remove the protective cover from the Professional Cappuccino Frother. T Connect the milk pipe to the nozzle. T Insert the other d of the milk pipe into a milk carton or connect to a milk container. T Place a cup under the nozzle. T Set the selector lever of the nozzle to the milk t posion. NA 3 HATING RADY appears as soon as the NA is sufficly heated. STAM, the hot milk is being prepared. y T Turn the swch clockwise to posion o wh there is suffic milk in the cup. You can prepare more hot milk whin about 40 seconds. To sure that the Professional Cappuccino Frother works perfectly, should be rinsed and cleaned regularly (refer to Chapter 4 Rinse Professional Cappuccino Frother ). Heating milk wh the 2-stage frothing nozzle Precondion: RADY is shown on the display. T Push the 2-stage frothing nozzle to the top posion. T Place a cup of milk below the 2-stage frothing nozzle and immerse the nozzle in the milk. If the nozzle does not reach into the cup, lift the cup towards the nozzle. g T Turn the Rotary Swch until STAM is g T Turn the Rotary Swch until STAM is HATING RADY appears as soon as the NA is sufficly heated. 19

20 NA 3 STAM, the milk is heated by the hot steam. y T Turn the swch to posion o as soon as the required temperature is reached. Hot water You can prepare more steam whin about 40 seconds. To sure that the 2-stage frothing nozzle works perfectly, should be rinsed regularly (refer to Chapter 4 Rinse Dismantling and rinsing the 2-stage frothing nozzle ). To prepare hot water, attach eher the hot water nozzle or the 2-stage frothing nozzle to the Connector System. J CAUTION There is a danger of scalding from hot water splashes. T Avoid direct contact wh the skin. Precondion: RADY is shown on the display. T Place a cup under the nozzle. WATR, hot water flows into the cup. y T Turn the swch clockwise wh there is suffic water in the cup. RADY 3 Default settings in programming mode Products The following settings can be programmed for 1 coffee: Z Amount of water: 25 ML 240 ML Z Coffee strgth: MILD, NORMAL, STRONG Z Temperature: NORMAL, HIGH The following applies wh preparing 2 coffees: Z The amount of water set for 1 coffee is dispsed per cup wh 2 cups are prepared. Z 2 coffees are always prepared wh the coffee strgth mild. Z 2 coffees are prepared at the same temperature which is set for 1 coffee. Default settings in programming mode always follow the same model. xample: Changing the default setting for the strgth of one coffee from NORMAL to STRONG. Precondion: RADY is shown on the display. T Op the cover behind the Rotary Swch. P T Press the P button until RINS appears. g T Turn the Rotary Swch until PRODUCT is k T Press the Rotary Swch to ter the programme em. WATR g T Turn the Rotary Swch until AROMA is k T Press the Rotary Swch to ter the programme em. NORMAL g T Turn the Rotary Swch until STRONG is k T Press the Rotary Swch to confirm the setting. OK, the coffee strgth is th adjusted. AROMA g T Turn the Rotary Swch until XIT is k T Press the Rotary Swch to ex the programme em. PRODUCT g T Turn the Rotary Swch until XIT is k T Press the Rotary Swch to ex programming mode. RADY 20

21 nergy-saving mode A default ergy-saving mode (nergy Save Mode,.S.M. ) setting can be selected on the NA. Programme em NRGY - / p: Z NRGY - U The NA is th in constant stand-by mode. U All coffee products as well as hot water can be prepared whout having to wa. Z NRGY p U After approx. 5 minutes the NA swches to the ergy-saving temperature and is not ready for use. U Before coffee or hot water is prepared, the machine heats up. xample: Changing the ergy-saving mode from NRGY - to NRGY p. Precondion: RADY is shown on the display. T Op the cover behind the Rotary Swch. P T Press the P button until RINS appears. g T Turn the Rotary Swch until NRGY - is k T Press the Rotary Swch to ter the programme em. CONOMY - g T Turn the Rotary Swch until CONOMY p is k T Press the Rotary Swch to confirm the setting. OK, the ergy-saving mode is th set. NRGY p g T Turn the Rotary Swch until XIT is k T Press the Rotary Swch to ex programming mode. RADY Automatic swch-off You can save ergy wh the automatic swchoff function on the NA. NA 3 The automatic swch-off time can be set to betwe 0.5 and 9 hours or deactivated (--- HRS). xample: Changing the automatic swch-off time from 1 HRS to 2 HRS. Precondion: RADY is shown on the display. T Op the cover behind the Rotary Swch. P T Press the P button until RINS appears. g T Turn the Rotary Swch until OFF AFTR is k T Press the Rotary Swch to ter the programme em. 1 HRS g T Turn the Rotary Swch until 2 HRS is k T Press the Rotary Swch to confirm the setting. OK, the automatic swch-off time is th adjusted. OFF AFTR g T Turn the Rotary Swch until XIT is k T Press the Rotary Swch to ex programming mode. RADY Uns of water The un for the amount of water can be displayed in eher ml or oz. xample: Changing the uns of water from ML to OZ. Precondion: RADY is shown on the display. T Op the cover behind the Rotary Swch. P T Press the P button until RINS appears. g T Turn the Rotary Swch until UNIT is k T Press the Rotary Swch to ter the programme em. ML g T Turn the Rotary Swch until OZ is 21

22 NA 3 k T Press the Rotary Swch to confirm the setting. OK, the uns of water are th adjusted. UNIT g T Turn the Rotary Swch until XIT is k T Press the Rotary Swch to ex programming mode. RADY Language The language is selected wh the machine is used for the first time. xample: Changing the language from NGLISH to FRANCAIS. Precondion: RADY is shown on the display. T Op the cover behind the Rotary Swch. P T Press the P button until RINS appears. g T Turn the Rotary Swch until LANGUAG is k T Press the Rotary Swch to ter the programme em. NGLISH g T Turn the Rotary Swch until FRANCAIS is k T Press the Rotary Swch to confirm the setting. OK, the language is th adjusted. LANGU g T Turn the Rotary Swch until XIT is k T Press the Rotary Swch to ex programming mode. PRT 4 Rinse The NA has the following integrated rinse programmes: Z Rinse machine Z Change filter Z Z Clean machine Descale machine Clean or descale the machine or change the filter whever the appropriate indicator lights up. Rinse tips To sure a long service life and the best possible coffee qualy, the NA requires the following daily care: Z mpty the coffee grounds container and drip tray and rinse wh warm water. Z Rinse the water tank wh clean water. Z Wipe the surface of the machine wh a damp cloth. Z Rinse the nozzle regularly if is used to warm or froth milk. Rinsing the machine manually Wh the NA is swched on, a prompt to perform a rinse operation automatically appears after heating. Wh the NA is swched off, the system is automatically rinsed if a coffee specialy has be prepared. The Rinse machine operation can be manually iniated. Precondion: RADY is shown on the display. T Place a receptacle under the coffee spout. T Op the cover behind the Rotary Swch. P T Press the P button until RINS appears. k T Press the Rotary Swch to ter the programme em. RINS k T Press the Rotary Swch to start rinsing. RINSING, rinsing stops automatically. RADY 22

23 NA 3 Changing the filter following a prompt After 50 lres of water have flowed through the filter, s capacy is reached. The NA automatically prompts you to replace the filter. After two months the filter capacy is reached. The elapsed time can be checked wh the date plate on the cartridge holder. If the CLARIS filter cartridge is not activated, you will not be prompted to change the filter. Precondion: RADY / FILTR is T Op the cover behind the Rotary Swch. c T Press the rinse button. INSRT FILTR T Remove and empty the water tank. T Op the cartridge holder and remove the old filter cartridge. T Insert the filter cartridge into the water tank, exerting slight pressure. T Close the cartridge holder. It will click into place audibly. T Fill the water tank wh cold, fresh water and replace the tank. T Place a receptacle (at least 500 ml) under the nozzle. OPN TAP FILTR RINSING, water is discharged from the nozzle. Rinsing of the filter can be interrupted at any time. To this purpose turn the swch clockwise. The water may be slightly discoloured. This is not harmful to health and does not affect the taste. Rinsing of the filter stops automatically, CLOS TAP. y T Turn the swch to posion o. HATING RADY Changing the filter manually The Change filter operation can be manually iniated. Precondion: RADY is shown on the display. T Op the cover behind the Rotary Swch. P T Press the P button until RINS appears. k T Press the Rotary Swch to ter the programme em. RINS g T Turn the Rotary Swch until FILTR is INSRT FILTR T Continue wh the third prompt to take action (indicated by T), as described in the section Changing the filter following a prompt. Cleaning the machine following a prompt After 180 coffee preparations or 80 swch-on rinses, the NA will prompt you to clean the machine. CAUTION If the wrong cleaning agt is used, the machine could be damaged and/or detergt residues could be left in the water. T Only use original JURA care products. 23

24 NA 3 The cleaning programme only lasts about 15 minutes. Do not interrupt the cleaning programme. The qualy of cleaning will be impaired if you do so. JURA cleaning tablets are available from stockists. Precondion: CLAN / RADY is T Op the cover behind the Rotary Swch. c T Press the rinse button. MPTY TRAY T mpty the coffee grounds container and drip tray and replace. PRSS ROTARY T Place a receptacle under the coffee spout. k T Press the Rotary Swch to start cleaning. CLANING, water flows out of the coffee spout. The process is interrupted. ADD TABLT T Op the powder chaft for pre-ground coffee and drop in a JURA cleaning tablet. T Close the powder chaft for pre-ground coffee. PRSS ROTARY CLANING, water flows out of the coffee spout several times. MPTY TRAY T mpty the coffee grounds container and drip tray and replace. RADY Cleaning the machine manually The Clean machine operation can be manually iniated. Precondion: RADY is shown on the display. T Op the cover behind the Rotary Swch. P T Press the P button until RINS appears. k T Press the Rotary Swch to ter the programme em. RINS g T Turn the Rotary Swch until CLAN is MPTY TRAY T Continue wh the third prompt to take action (indicated by T), as described in the section Cleaning the machine following a prompt. Descaling the machine following a prompt The NA builds up limescale deposs over time and automatically prompts you to descale the machine wh necessary. The degree of build-up depds on the hardness of the water. J CAUTION If the descaling agt comes into contact wh the skin or eyes, this can cause irration. T Avoid contact wh the skin or eyes. T Rinse the descaling agt off wh clean water. Should you get any descaling agt in your eye, consult a doctor. CAUTION Risk of damage to the machine and residues in the water if the wrong descaling agt is used. T Only use original JURA care products. CAUTION Risk of damage to the machine if the descaling operation is interrupted. T Do not interrupt the descaling operation. 24

25 CAUTION Risk of damage if the descaling agt comes into contact wh ssive surfaces. T Remove splashes immediately. The descaling programme lasts approx. 40 minutes. JURA descaling tablets are available from stockists. If a CLARIS filter cartridge is used and activated, you will not be prompted to descale the machine. Precondion: D-SCAL / RADY is T Op the cover behind the Rotary Swch. c T Press the rinse button. MPTY TRAY T mpty the coffee grounds container and drip tray and replace. AGNT IN TANK T Remove and empty the water tank. T Completely dissolve the contts of one blister (3 JURA descaling tablets) in a container holding 500 ml of water. This may take several minutes. NA 3 D-SCALING, water flows out of the Connector System several times. CLOS TAP y T Turn the swch to posion o. D-SCALING, the descaling operation is continued. MPTY TRAY T mpty the coffee grounds container and drip tray and replace. T mpty the receptacle and place under the Connector System once more. FILL WATR TANK T Remove the water tank, rinse thoroughly, fill wh fresh, cold water and replace the tank. OPN TAP D-SCALING, water flows out of the Connector System several times. The process is interrupted, CLOS TAP. y T Turn the swch to posion o. D-SCALING, the descaling operation is continued. MPTY TRAY T mpty the coffee grounds container and drip tray and replace. T Reattach the nozzle to the Connector System. RADY T Pour the solution into the empty water tank and replace the tank. OPN TAP T Carefully remove the nozzle from the Connector System. T Place a receptacle (at least 500 ml) under the Connector System. Descaling the machine manually The Descale machine operation can be manually iniated. Precondion: RADY is shown on the display. T Op the cover behind the Rotary Swch. P T Press the P button until RINS appears. k T Press the Rotary Swch to ter the programme em. RINS g T Turn the Rotary Swch until D-SCAL is 25

26 NA 3 MPTY TRAY T Continue wh the third prompt to take action (indicated by T), as described in the section Descaling the machine following a prompt. Rinsing the Professional Cappuccino Frother To sure that the Professional Cappuccino Frother works perfectly, you should rinse wh water whever you have prepared some milk. The NA will not prompt you to rinse the Professional Cappuccino Frother. T Remove the milk pipe from the milk carton or milk container. T Fill a receptacle wh fresh water and immerse the milk pipe in the water. T Place another receptacle under the nozzle. T Set the selector lever of the nozzle to the milk foam p or milk t posion. Cleaning the Professional Cappuccino Frother To sure that the Professional Cappuccino Frother works perfectly, you should clean daily wh you have be preparing milk. CAUTION If the wrong cleaning agt is used, the machine could be damaged and/or detergt residues could be left in the water. T Only use original JURA care products. The NA will not prompt you to clean the Professional Cappuccino Frother. The JURA Cappuccino Cleaner is available from stockists. T Remove the milk pipe from the milk carton or milk container. T Pour 250 ml of fresh water into a receptacle and add one capful (max. 15 ml) of Cappuccino Cleaner. T Immerse the milk pipe in the receptacle. T Place another receptacle under the nozzle. T Set the selector lever of the nozzle to the milk foam p or milk t posion. g T Turn the Rotary Swch until STAM is HATING RADY appears as soon as the NA is sufficly heated. STAM, the nozzle and pipe are rinsed. y T Turn the swch to posion o as soon as clean water flows into the receptacle. g T Turn the Rotary Swch until STAM is HATING RADY appears as soon as the NA is sufficly heated. STAM, the nozzle and pipe are cleaned. y T Turn the swch clockwise to posion o as soon as the receptacle holding the Cappuccino Cleaner is empty. 26

27 T Rinse the receptacle thoroughly, fill wh 250 ml of fresh water and immerse the milk pipe in the water. T mpty the receptacle under the nozzle and replace under the nozzle. g T Turn the Rotary Swch until STAM is HATING RADY appears as soon as the NA is sufficly heated. STAM, the nozzle and pipe are rinsed wh fresh water. y T Turn the swch clockwise to posion o as soon as the receptacle holding the water is empty. Dismantling and rinsing the Professional Cappuccino Frother T Carefully remove the Professional Cappuccino Frother from the Connector System. T Dismantle the frother completely. T Rinse all parts thoroughly wh running water. T Reassemble the Professional Cappuccino Frother and attach to the Connector System. Rinsing the asy Cappuccino Frother To sure that the asy Cappuccino Frother works perfectly, you should rinse wh water whever you have prepared some milk. The NA will not prompt you to rinse the asy Cappuccino Frother. NA 3 T Remove the milk pipe from the milk carton or milk container. T Fill a receptacle wh fresh water and immerse the milk pipe in the water. T Place another receptacle under the nozzle. g T Turn the Rotary Swch until STAM is HATING RADY appears as soon as the NA is sufficly heated. STAM, the nozzle and pipe are rinsed. y T Turn the swch to posion o as soon as clean water flows into the receptacle. Cleaning the asy Cappuccino Frother To sure that the asy Cappuccino Frother works perfectly, you should clean daily wh you have be preparing milk. CAUTION If the wrong cleaning agt is used, the machine could be damaged and/or detergt residues could be left in the water. T Only use original JURA care products. The NA will not prompt you to clean the asy Cappuccino Frother. The JURA Cappuccino Cleaner is available from stockists. 27

28 NA 3 T Remove the milk pipe from the milk carton or milk container. T Pour 250 ml of fresh water into a receptacle and add one capful (max. 15 ml) of Cappuccino Cleaner. T Immerse the milk pipe in the receptacle. T Place another receptacle under the nozzle. Dismantling and rinsing the asy Cappuccino Frother T Carefully remove the asy Cappuccino Frother from the Connector System. T Dismantle the nozzle completely. g T Turn the Rotary Swch until STAM is HATING RADY appears as soon as the NA is sufficly heated. STAM, the nozzle and pipe are cleaned. y T Turn the swch clockwise to posion o as soon as the receptacle holding the Cappuc cino Cleaner is empty. T Rinse the receptacle thoroughly, fill wh 250 ml of fresh water and immerse the milk pipe in the water. T mpty the receptacle under the nozzle and replace under the nozzle. g T Turn the Rotary Swch until STAM is HATING RADY appears as soon as the NA is sufficly heated. STAM, the nozzle and pipe are rinsed wh fresh water. y T Turn the swch clockwise to posion o as soon as the receptacle holding the water is empty. T Rinse all nozzle parts thoroughly wh running water. T Reassemble the asy Cappuccino Frother and attach to the Connector System. Dismantling and rinsing the 2-stage frothing nozzle To sure that the 2-stage frothing nozzle functions correctly, clean regularly if you have heated or frothed milk. J CAUTION Danger of burns from the hot nozzle and nozzle connector. T Wa until the nozzle has cooled before cleaning. T Carefully remove the nozzle from the Connector System. T Unscrew the nozzle using the hole on the measuring spoon for pre-ground coffee. 28

29 NA 3 T Rinse all three nozzle parts thoroughly under running water. T Reassemble the nozzle and attach to the Connector System. Cleaning the bean container Coffee beans may be covered wh a slight oil film which remains on the walls of the bean container. These residues may negatively affect the coffee results. For this reason clean the bean container from time to time. Q T Press the on/off button to swch the machine off. T Disconnect the mains plug. T Remove the bean container cover. T Remove the coffee beans wh a vacuum cleaner. T Clean the bean container wh a soft, dry cloth. T Fill the bean container wh fresh coffee beans, th close the bean container cover. Descaling the water tank Limescale deposs may form in the water tank. To sure correct function of the machine, descale the water tank from time to time. T Remove the water tank. T If a CLARIS filter cartridge is used, remove the cartridge. T Descale the tank wh a mild, commercially available descaling agt in accordance wh the instructions of the manufacturer. T Rinse the water tank thoroughly. T If a CLARIS filter cartridge is used, replace the cartridge. T Fill the water tank wh cold, fresh water and replace the tank. 29

30 NA 3 5 Display messages Message Cause/Result Action FILL WATR TANK MPTY GROUNDS TRAY MISSING FILL BANS CLAN D-SCAL FILTR NOT NOUGH PR-GROUND TOO HOT The water tank is empty. You cannot prepare any coffee specialies, hot water or steam. The coffee grounds container is full. You cannot prepare any coffee specialies, but you can prepare hot water or steam. The drip tray is not inserted correctly or is not inserted at all. You cannot prepare any coffee specialies, hot water or steam. The bean container is empty. You cannot prepare any coffee specialies, but you can prepare hot water or steam. The NA is prompting you to clean the machine. The NA is prompting you to descale. Once 50 lres of water have flowed through the CLARIS filter cartridge, s capacy is reached. There is too ltle pre-ground coffee in the machine. The NA stops the operation. The system is too hot to begin a rinse programme. T Fill the water tank (refer to Chapter 1 Preparing and using for the first time Filling the water tank ). T mpty the coffee grounds container and the drip tray. T Insert the drip tray. T Fill the bean container (refer to Chapter 1 Preparing and using for the first time Filling the bean container ). T Clean the machine (refer to Chapter 4 Rinse Cleaning the machine following a prompt ). T Descale the machine (refer to Chapter 4 Rinse Descaling the machine following a prompt ). T Replace the CLARIS filter cartridge (refer to Chapter 4 Rinse Replacing the filter following a prompt ). T The next time you make coffee use more pre-ground coffee (refer to Chapter 2, Preparation Pre-ground coffee ). T Wa for several minutes until the system has cooled or prepare a coffee specialy or hot water. 30

31 NA 3 6 Troubleshooting Problem Cause/Result Action Grinder is making a very loud noise. There are foreign objects in the grinder. T Contact customer support in your country. Contact information is available on the company webse at com. The nozzle does not produce ough milk foam. The nozzle is eher in the wrong posion or is dirty. T Adjust the posion of the nozzle (refer to Chapter 2 Preparation Cappuccino ). T Rinse the nozzle (refer to Chapter 4 Rinse Rinsing the nozzle ). Coffee only drips out during preparation. Water hardness cannot be adjusted. Coffee or pre-ground coffee has be ground too finely and is blocking the sieve. The CLARIS filter cartridge is activated. T Adjust the grinder or use coarser preground coffee (see Chapter 1, Preparing and using for the first time Adjusting grinder ). T Deactivate the CLARIS filter cartridge in programming mode. FILL BANS is displayed although the bean container has be filled. The grinder is not yet completely filled wh beans. T Prepare a coffee specialy. FILL WATR TANK is displayed although the water tank is full. The water tank float is trapped. T Descale the water tank (refer to Chapter 4 Rinse Descaling the water tank ). RROR 2 is If the device is exposed to the cold for a long period of time, the heating function is disabled for safety reasons. T Wa until the machine has reached room temperature. Other RROR messages are T Swch the NA off wh the on/off button. Contact customer support in your country. Contact information is available on the company webse at If you have not be able to solve the problem, contact customer support in your country. Contact information is available on the company webse at 31

32 NA 3 7 Transport and vironmtally neutral disposal Transport/mptying the system Keep the packaging of your NA. It should be used to protect the machine during transportation. In order to protect the NA from frost during transportation, the system must be emptied. Precondion: RADY appears on the display. g T Turn the Rotary Swch until STAM is HATING RADY appears as soon as the NA is sufficly heated. STAM, hot steam is discharged from the nozzle. T Remove and empty the water tank. Steam will continue to be discharged from the nozzle until the system is empty. CLOS TAP Q T Press the on/off button to swch the machine off. y T Turn the swch to posion o. The next time you use the machine the system must be refilled (see Chapter 1, Preparing and using for the first time First-time use ). 8 Technical data Voltage Power Safety test Power consumption CONOMY - Power consumption CONOMY p Pump pressure Holding capacy of water tank Holding capacy of bean container Holding capacy of coffee grounds container Cable lgth Weight Dimsions (W x H x D) A S 230 V AC, 50 Hz F 120 V AC, 60 Hz D V AC, 50 Hz G 220 V AC, 50 Hz 1450 W S F D G Approx Wh Approx. 8 Wh Static max. 15 bar 1.1 l 125 g Approx. 10 servings Approx. 1.1 m Approx. 9.3 kg 23.8 x 36 x 44.5 cm Disposal Please dispose of old machines in an vironmtally neutral way. H 9 Contact information is available on the company webse at Old machines contain valuable materials which should be salvaged for recycling. Please therefore dispose of old machines via your regional collection system. 32

33 Index A B C D 2-stage frothing nozzle 8, 9 Dismantling and rinsing 28 3-colour plain text display 12 Adjusting Grinder 14 Language 22 Uns of water 21 Automatic swch-off 21 Bean container Cleaning 29 Filling 12 Cappuccino Wh the 2-stage frothing nozzle 18 Wh the asy Cappuccino Frother 18 Wh the Professional Cappuccino Frother 17 Cleaning asy Cappuccino Frother 27 Machine 23 Professional Cappuccino Frother 26 Coffee At the touch of a button 15 Pre-ground 16 Coffee grounds container 8 Coffee spout Height-adjustable 8 Connector System 8, 11 Contacts 32 Cover 9 Bean container 8 Cup platform 8 Descaling JURA descaling tablets 24 Machine 24 Water tank 29 Dismantling and rinsing 2-stage frothing nozzle 28 asy Cappuccino Frother 28 F G H I K M Professional Cappuccino Frother 27 Display 9 Messages 30 Disposal nvironmtally neutral disposal 32 Drip tray 8 asy Cappuccino Frother 9 Cleaning 27 Dismantling and rinsing 28 Rinsing 27 Filter Changing 23 Using and activating filter 13 First-time use 12 Grinder Adjusting grinder 14 Grinding wheel 9 NA 3 Heating milk Wh the 2-stage frothing nozzle 19 Wh the Professional Cappuccino Frother 19 Height-adjustable coffee spout 8 Hot water 20 Hot water nozzle 9 Internet JURA on the Internet 11 Knowledge Builder 11 Knowledge Builder 11 Machine Cleaning 23 Descaling 24 Rinsing 22 Swching off 15 Swching on 15 33