GAS ROTISSERIE GRANDES FLAMMES RANGE. Réf.: G G G G G G G 975.8G 975.6G 975.5G 975.4G 975.

Size: px

Start display at page:

Download "GAS ROTISSERIE GRANDES FLAMMES RANGE. Réf.: G G G G G G G 975.8G 975.6G 975.5G 975.4G 975."

Aubrey Fields
5 years ago
Views:

GAS ROTISSERIE GRANDES FLAMMES RANGE Réf.: 167.8G 137.12G 137.8G 137.6G 137.G 137.4G 137.2G 97.8G 97.6G 97.G 97.4G 97.

1 GAS ROTISSERIE GRANDES FLAMMES RANGE Réf.: 167.8G G 137.8G 137.6G 137.G 137.4G 137.2G 97.8G 97.6G 97.G 97.4G 97.2G INSTALATION MANUAL 341 North Oak Street, INGLEWOOD, CA Tél.: (310) Fax: (310) info@rotisolusa.com

2 1. TECHNICAL SPECIFICATIONS OF THE DEVICE 1.1. GENERAL Rôtisserie range " Grandes Flammes" gas powered with electrical power of 230V + earth. Référence Lenght (mm) depth (mm) Height (mm) weight (kg) Gas power (kw) Electrical power (kw) 167.8G , G , G , G ,6 137.G , 137.4G , G , G , G ,4 97.G ,3 97.4G , G ,29 The device is for professional use and should be used by qualified personnel. Before starting any operation, please see these instructions. Carefully keep available near the rotisserie. The upgrading of premises are at users expense. Every cooking appliance generates heat and particles of fat. The unit should be installed in accordance within norm's and regulations in force in a well-ventilated area. With sufficient mechanical extraction and fire prevention. Would recommend that you call upon a qualified company for the work to be done according to the local norm's extraction, gas connection, building work. We recommend that you call upon a qualified installer for the connection of the unit to the gas and electrical supplies. Interventions on the electrical parts must be performed by qualified personnel accordance with the standards. The company is not liable for damages if: improper use of the device non-compliance with standards incorrect installation non compliance with guidance on maintenance unauthorized modification installation of non-original spare parts installation and use of the rotisserie different than those provided by the mnufacturer The plate is located on the back right in the middle of the amount TRADEMARK, MODEL, REFERENCE Rôtissoires ROTISOL, model «GRANDES FLAMMES MILLENIUM», référence: 167.8G, G, 137.8G, 137.6G, 137.G, 137.4G, 137.2G, 97.8G, 97.6G, 97.G, 97.4G et 97.2G.

3 1.3. SITE OF MANUFACTURERS PLATE It is situated on the rear, right hand side of the unit. Rear of the rotisserie ELECTRICAL CONNECTION GAS INLET

4 1.4. COMPULSORY MARKINGS ON THE ROTISSERIE AND ON THE PACKING

5 2. SETTING UP UNIT AND STARTING UP Before connecting and starting up the rotisserie. Ensure that the gas and electrical connections are present. This work are at the client cost, that he needs to have done by are a agreed company, near the position that the rotisserie is to be les faire exécuter, par des sociétés. The new air flow require for the combustion is : 2 m 3 /h par kw of the calorifique flow SETTING UP UNPACKING Unpack the rotisserie that is circled, filmed and fixed on palette INSTALLING THE UNIT NEXT TO WALLS AND APPLIANCES The unit with glace door open should be placed at a distance minimum of 20mm to adjacent walls APPLIANCE EQUIPPED WITH WHEELS The device must be placed on a perfectly level ground and locked in a stationary position for use and et le stockage ENVIRONNEMENT The device should not be installed near the steam,grease (frying, ), projections of water, high températures or other adverse condition GAS CONNECTION The gas supply pipe will be sized to minimize losses power. It s diameter will be determined in function to it s route (length, number of bends etc...) and the total power rating of the unit. «Check that the settings of the unit corespond to the nature and preassure of the gas at the premises. In order to check the pressure of the unit, you just need to attached a manometer to the water gage at the gas inlet on the rear of the unit, with all the burners on full. The pressure measured should be the same as that indicated on the gas label, stuck to the unit. The gas supply valves require no rotisserie set-up during their lifetime GAS CIRCUIT DIAGRAM Gas connection Ø 20/27 Gas stopcock Pilot Maxitrol regulator Thermocouple Burner Knob ring Injector / Injector Support Adjusting ring of the primary air Gas cock Gas knob Gas line

6 POSITION OF THE THERMOCOUPLE & PILOT LIGHT POSITION OF THE INJECTOR AND THE SLEEVE FOR THE AJUSTMENT OF THE PRIMARY AIR.

7 FIXED INSTALATION MOBILE INSTALATION FIXED Connection type union 1 or 2 The use of TURBOGAS or similar in professional fixed instalations,willpermit a total liberty in the conception of the kitchen. MOBILE The conception of a kitchen with mobile gas appliance is possible thanks to a tamdem of TURBOGAZ - TUSHGAS or SIMILAR. FLEXIBLE PIPPING IN THE SHAPE OF U Measure of the gas flow under 20 mbar in kw/h PCI(natural gaz)

8 2.3. ELECTRICAL CONNECTION Check that there is no errors with CONNECTION. Electrical rating : 230V~0Hz. Check that the installed power corresponds with the characteristics on the signal plate at the rear of the unit EVACUATION - SMOKE TYPE : A IN ALL CASES, CONNECT THE EARTH WIRE THE UNIT IS DELIVERED IN MONOPHASE + EARTH The unit is destined to be installed under an extraction system with ventilation A heat delector with holes is placed above the rotisserie VIEW FROM ABOVE Reference 167-8G G 137-8G 137-6G 137-G 137-4G 137-2G 97-8G 97-6G 97-G 97-4G 97-2G Measurement A (mm) Measurement B (mm)

9 3. ADAPTING THE UNIT IN THE CASE OF CHANGING FROM ONE GAS TO ANOTHER 3.1. CHANGING THE INJECTOR GAS SUPPLY PIPE ELBOW NUT OF 90 TIGHTENING RINGS INJECTOR HOLDER INJECTOR ELBOW OF 90 AIR INLET SLEEVE ELBOW NUT OF ADJUSTMENT OF THE PRIMARY AIR SLEEVE FOR THE ADJUSTMENT OF PRIMARY AIR You need to adjust the opening of the air sleeve to dim. D coresponding to the type of gas used ( see position of the air sleeve, chapter and the table of adjustment of the burner, chapter 3.7) TABLE FOR ADJUSTMENT OF ONE BURNER BURNER MODEL CARACTERISTICS G20 under 20 mbar G2 under 2 mbar G31 under 37 mbar G31 under 0 mbar Heat flow in kw injector making Diamete rof injector in mm 2,4 2,4 1,6 1, GF 97 Opening of the primary air «D» in mm (chapitre 2.2.3) Flow volumein m 3 /h 2, 1,06 2, 1, Mass flow kg/h - - 0,776 0,776 Reduced heat flow in KW Presure at the tap for the reduced flow in mbar 6, 9, 12, Heat flow in kw injector making Diamete rof injector in mm 2,9 2,9 2 1,8 GF 137 Opening of the primary air «D» in mm (chapitre 2.2.3) Flow volumein m 3 /h 2, 1,9 2, 1,8-4 - Mass flow kg/h - - 1,16 1,16 Reduced heat flow in KW 7, 7, 7, 7, Presure at the tap for the reduced flow in mbar 6, 9, 12, Heat flow in kw injector making Diamete rof injector in mm 3,1 3,1 2,1 1,9 GF 167 Opening of the primary air «D» in mm (chapitre 2.2.3) Flow volumein m 3 /h 13, 1,8 13, 2, Mass flow kg/h - - 1,32 1,32 Reduced heat flow in KW 8, 8, 8, 8, Presure at the tap for the reduced flow in mbar 9, 12,

13 3.4. LABEL SET The label specifying the setting of gas to the appliance must be attached to it (see mandatory, chapter ). In case of change of gas, the new label comes with the new injectors. 3.. ADJUSTEMENT OF THE REDUCE FLOW ADJUSTMENT OF REDUCED FLOW Connect a manometeron the pressure plug and adjust to the pressure required ( see table of : categuories of gas, chapter 3.1.1) with the aide of the reduced flow screw: SEAL THE ADJUSTMENT ADJUSTMENT OF LOW SETTING Put the tap to the «minimum» setting. Connect a manometer on the preassure plug and adjust the pressure to that require ( see table for adjustment of burner, chapter 3.7) with the aide of the low setting screw. SEAL THE ADJUSTMENT

14 3.6. TABLE FOR THE ADJUSTMENT OF THE SECONDARY AIR MODEL SHUTER Dim «S» in G20 under 20 mbar Dim «S» in G2 under 2 mbar Dim«S» in G31 under 37 mbar Dim «S» in G31 under 0 mbar GF 97-2 UPPER GF 97-4 UPPER MIDDLE GF 97- UPPER MIDDLE UPPER GF 97-6 MIDDLE LOWER UPPER GF 97-8 MIDDLE LOWER GF UPPER GF UPPER MIDDLE GF 137- UPPER MIDDLE UPPER GF MIDDLE LOWER UPPER GF MIDDLE LOWER UPPER GF MIDDLE LOWER UPPER GF MIDDLE LOWER

15 4. ELECTRICAL DRAWING For the rotisserie 167.8, there are 8 motors and 2 halogen lamps. For the rotisserie , there are 6 motors and 1 halogen lamp. For the rotisserie 137.8, there are 8 motors and 1 halogen lamp. For the rotisserie 137.6, there are 6 motors and 1 halogen lamp. For the rotisserie 137., there are motors and 1 halogen lamp. For the rotisserie 137.4, there are 4 motors and 1 halogen lamp. For the rotisserie 137.2, there are 3 motors and 1 halogen lamp. For the rotisserie 97.8, there are 8 motors and 1 halogen lamp. For the rotisserie 97.6, there are 6 motors and 1 halogen lamp. For the rotisserie 97., there are motors and 1 halogen lamp. For the rotisserie 97.4, there are 4 motors and 1 halogen lamp. For the rotisserie 97.2, there are 3 motors and 1 halogen lamp.

16 . SPARE PARTS.1 CENTRE PART.1.1 NOMENCLATURE REP DESIGNATION QTE REFERENCE GRANDES FLAMMES MODEL 1 BASE G G GF FRAME DEFLECTEUR WITH HOLES 1 DES DES DES BANNER 1 GFG GFG GFG PARABOLE TYPE G G GF GLASS HOLD G SUPPORT HALOGENE G SUPPORT HALOGENE LAMP 2 SUPR7S HALOGENE LAMP 2 LA78NM GLASS 2 PLAVERRE GLASS BLOCKING AT HALOGENE G G SUPPORT LEFT OF TRAY G SUPPORT RIGHT OF TRAY G

17 REP DESIGNATION QTE REFERENCE MODELE GRANDES FLAMMES MODEL (follow) MIDLE DRIP TRAY 1 PLAT16H 167 PLAT137H 137 PLAT90H 97 1 DRAIN PLUG 1 BV DRAIN PLUG 1 BV000 TOUT LES MODELES 17 DRIP TRAY 1 PLAT16GT PLAT13GT PLAT96GT SUPPORT BURNER 3 SUPPORT BRULEUR (167) SUPPORT BRULEUR (137) SUPPORT BRULEUR (97) BURNER 3 BRU160NM BRU130NM BRU97NM BURNER COVER 3 GFC160 + GFCA GFG GFCA SUPPORT OF CAST IRON PLATE 3 SPP (see next page) 3 SPP

18 REP DESIGNATION QTE REFERENCE MODELE GRANDES FLAMMES (suite) SPP CAST IRON PLATE 27 PLPICOT PLPICOT166 (1) B SAMLL CAST IRON PLATE 3 PLPICOT SPACER CAST IRON PLATE 6 GFG AXE CAST IRON PLATE 3 ROND12/ ROND12/ ROND12/ BLOCKING ROD CAST IRON PLATE 6 TIGE ISULATION 3 NEFALIT NEFALIT NEFALIT7 97-8

19 REP DESIGNATION QTE REFERENCE GRANDES FLAMMES MODEL (follow) VAUGIRARD PLATE MIDDLE / LOWER 48 BRI22041 (1) SUPPLEMENT BRICK MIDDLE / LOWER G GFG BRICK HOLDER MIDDLE / LOWER 2 GFMAIN GFG GFMAIM SUPPORT BRICK MIDDLE / LOWER 2 GFAR GFG GFAR VAUGIRARD PLATE UPPER 24 BRI SUPPLEMENT BRICK UPPER G GFG BRICK HOLDER UPPER 1 GGFMI

20 REP DESIGNATION QTE REFERENCE GRANDES FLAMMES MODEL (follow) 1 GFG GFMI TIGHTNER FOR REAR FRAME 3 RA8B GFG SUPPORT FOR UPPER BRICKS 3 GFAR9BNM GFG GFARBRH GFA98NM GFARBET AJUSTER OF AIR INTAKE 3 GFREG GFG GFREG REAR 3 GFAR GFG GFAR REAR LOWER PLATE 1 GF16CU GFG GF93CU10 97

21 .1.2. EXPLODED VIEW

22 .2 RIGHT SIDE.2.1. NOMENCLATURE REP DESIGNATION QTE REFERENCE GRANDES FLAMMES MODEL 1 RIGHT MOUNT G GFG G G TIGHTENER RIGHT MOUNT G G G UPPER PART RIGHT MOUNT G40 TOUT LES MODELES 4 U RIGHT MOUNT G42 TOUT LES MODELES EXTERIOR PANEL RIGHT G GFG2I G G STOP FOR EXTERIOR PANEL G18 TOUT LES MODELES 7 MOTOR SPG 8 MOTEUR SPG GF MOTOR AXEL 8 EXA SUPPORT PLATE FOR MOTOR 8? (see next page) 137-

23 REP DESIGNATION QTE REFERENCE MODELE GRANDES FLAMMES (following) ILSDER FOR MOTOR SUPPORT 16 PERER PROTECTION FOR MOTOR 8 GF TERMINAL SUPPORT G08 TOUT LES MODELES 13 TERMINAL 1 BORAL904A TOUT LES MODELES 14 WIRE PASS 1 PRETH03302M TOUT LES MODELES 1 SWITCH 8 COMROT INDICATOR PLATE 8 GFG SWITCH BOUTON 2 BOUCOM0 TOUT LES MODELES 18 SWITCH BOUTON 8 BOUCOM (see next page) 97-4

24 REP DESIGNATION QTE REFERENCE GRANDES FLAMMES MODEL (following) BRASS RIND FOR INDICATOR LIGHT 1 BVRL1216 TOUT LES MODELES 20 INDICATOR LIGHT 1 VOYRCUL TOUT LES MODELES BRASS ROD 1 LAI8B LAIB LAI2B BRASS ROD 1 LAI8B LAIB LAI2B BRASS ROD 1 LAI8B LAIB LAI2B BRASS ROD 1 LAI8B LAIB LAI2B DOOR STOPPER 2 ARRET (see next page) 97-8

25 REP DESIGNATION QTE REFERENCE GRANDES FLAMMES MODEL (following) MOTOR COVER G GFG E HINGE 4 CHAGF CHAGF HINGE JOINT 8 GF GF GLASS DOOR 2 GL216B GL21B GL214B GL211B 137- GL211B GL210B GL208B GL207B KNOB FOR GLASS DOOR 2 BTU704AD ou LP BTU704AD ou LP

26 .2.2. EXPLODED DRAWING RIGHT SIDE

27 .3 LEFT PART.3.1. NOMENCLATURE REP DESIGNATION QTE REFERENCE MODELE GRANDES FLAMMES 1 LEFT MOUNT G GFG ? ? TIGHTNER LEFT MOUNT G G ? UPPER PART LEFT MOUNT G39 TOUT LES MODELES 4 U LEFT MOUNT G41 TOUT LES MODELES EXTERIOR PANEL LEFT G GFG2I ? STOP FOR EXTERIOR PANEL G18 TOUT LES MODELES 7 SPIT SUPPORT G G E SUPPORT PLATE FOR SPIT BRASS G PILOT COVER 3 GFCAVEI (see following page)

28 REP DESIGNATION QTE REFERENCE GRANDES FLAMMES MODEL (followin) VENTURIE COVER 3 GF AIR SLEEVE 3 BAGVEN AIR INLET SLEEVE 3 VENECO TAPERED THREAD INJECTOR 3 INJ400 (1) INJ290 (1) INJ20 / 240 / 16 (1) INJECTOR HOLDER 3 PI6119A ELBOW JOINT BRASS 3 RLC12SM (1) see type of gas (see following page) 137-8

29 REP DESIGNATION QTE REFERENCE GRANDES FLAMMES MODEL (following) PIPE VALVE BURNER 3 TUBE GAS VALVE 3 ROBS PIPE PILOT VALVE 3 137TG PILOT 3 V1092A (1) THERMOCOUPLE 3 THER600 (1) (see following page) 97-2 (1) thermocouple and pilot in one piece Ref : THERMOJADE

30 REP DESIGNATION QTE REFERENCE GRANDES FLAMMES MODEL 21 PIPE PLUG 1 BFF2027 TOUT LES MODELES 22 GAS RAMP 1 RAMGF8BR RAMGFBR RAMGF2BR ATLAS COLLAR 3 COL26 TOUT LES MODELES 24 BLACK CAST IRON ELBOW 1 COU90 TOUT LES MODELES 2 INCLINE PIPE 1 MAM8322 TOUT LES MODELES 26 CAST IRON JOINT 1 UFT2027 TOUT LES MODELES 27 PLASTRON ROBINET GAZ 3 GF GAS KNOB 3 BOUROB FRONT ENAMEL GAS G DOOR STOP 4 ARRET BRASS ROD 1 LAI8B ollowing page..) 137-8

31 REP DESIGNATION QTE REFERENCE GRANDES FLAMMES MODEL LAIB LAI2B BRASS ROD 1 LAI8B LAIB LAI2B BRASS ROD 1 LAI8B LAIB LAI2B BRASS ROD 1 LAI8B LAIB LAI2B HINGE 4 CHAGF CHAGF HINGE JOINT 8 GF GF (see follong page..) 97-2

32 REP DESIGNATION QTE REFERENCE GRANDES FLAMMES MODEL 37 GLASS DOOR 2 GL216B GL21B GL214B GL211B GL210B GL208B GL207B KNOB GLASS DOOR 2 BTU704AD ou LP BTU704AD ou LP

33 .3.2. EXPLODED LEFT VIEW

Performer II Series Convection Oven

US RANGE Performer II Series Convection Oven Performer II Series Convection Oven 612 Performer II Convection Oven 1 282285 Motor Guard 1A 228129 Motor Only - 1/4 HP 1B 252757 Motor Pad Assembly 2 228130